2011-2016 FJ Cruiser · Service Manual ENGINE

P2111 Throttle Actuator Control System - Stuck Open

Diagnostic trouble codes · Vehicles built Jul 2007 – Nov 2007

Also covers:

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 from Aug 2009

DESCRIPTION

The throttle motor is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle body. The TP sensor provides feedback to the ECM in order that it can control the throttle motor, and therefore the throttle valve, appropriately in response to driver inputs.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC No.
DTC Detection Conditions
Trouble Areas
P2111
ECM signals throttle motor to close, but stuck (1 trip detection logic)
  1. Throttle with motor body assembly
  2. Throttle valve
P2112
ECM signals throttle motor to open, but stuck (1 trip detection logic)

MONITOR DESCRIPTION

The ECM determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set when the accelerator pedal is fully depressed and released quickly (to fully open and close the throttle valve) after the engine is next started.

FAIL-SAFE

When either of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle motor off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed.
If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned OFF.

WIRING DIAGRAM

Refer to DTC P2102 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P2111 or P2112
    A
    P2111 or P2112 and other DTCs
    B

    HINT:
    If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
  1. Check for contamination between the throttle valve and the housing. If necessary, clean the throttle body. And check that the throttle valve moves smoothly.

    OK:
    Throttle valve is not contaminated with foreign objects and moves smoothly.



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine, and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    No DTC
    A
    P2111 or P2112
    B



B
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)


← P2109 Throttle / Pedal Position Sensor "A" Minimum Stop Performance (from Aug 2014)P2111 Throttle Actuator Control System - Stuck Open (+ P2112) (Dec 2007 – Jul 2009) →