2011-2016 FJ Cruiser · Service Manual ENGINE

P2102 Throttle Actuator Control Motor Circuit Low

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

The throttle motor built into the throttle body is operated by the ECM and opens and closes the throttle valve using gears.
The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle body. The TP sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC No.
DTC Detection Conditions
Trouble Areas
P2102
Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic)
  1. (a) Throttle motor duty ratio 80 % or more
  2. (b) Throttle motor current 0.5 A or less
  1. Open in throttle motor circuit
  2. Throttle with motor body assembly
  3. ECM
P2103
Either of following conditions met (1 trip detection logic):
  1. Hybrid IC diagnosis signal fail
  2. Hybrid IC current limiter port fail
  1. Short in throttle motor circuit
  2. Throttle with motor body assembly
  3. ECM

MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and sets a DTC.
Example:
When the electrical current is less than 0.5 A and the throttle motor duty ratio exceeds 80%, the ECM interprets this as the current being outside the standard range, and illuminates the MIL and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set when the engine is quickly revved to a high rpm several times after the engine has idled for 5 seconds after engine start.

FAIL-SAFE

When either of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle motor off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned OFF.

WIRING DIAGRAM

A133489E07

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
  2. The throttle actuator current [Throttle Motor Current] and the throttle actuator duty ratio [Throttle Motor Duty (Open) / Throttle Motor Duty (Close)] can be read using an intelligent tester. However the ECM shuts off the throttle actuator current when the ETCS malfunctions.


1. INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE CONTROL MOTOR)
A059778E57
  1. Disconnect the B14 throttle with motor body connector.

  1. Measure the resistance between the terminals of the throttle control motor.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    M+ (2) - M- (1)
    0.3 to 100 Ω at 20°C (68°F)

  1. Reconnect the throttle with motor body connector.



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY - ECM)
A116167E07
  1. Disconnect the B14 throttle with motor body connector.

  1. Disconnect the B1 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    M+ (B14-2) - M+ (B1-5)
    Below 1 Ω
    M- (B14-1) - M- (B1-4)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    M+ (B14-2) or M+ (B1-5) - Body ground
    10 kΩ or higher
    M- (B14-1) or M- (B1-4) - Body ground

  1. Reconnect the throttle with motor body connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check for foreign objects between the throttle valve and the housing.

    OK:
    No foreign objects between throttle valve and housing.



NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY
OK


4. INSPECT THROTTLE VALVE
  1. Check if the throttle valve opens and closes smoothly.

    OK:
    Throttle valve opens and closes smoothly.



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)


← P1613 Secondary Air Injection System Driver (from Aug 2014)P2102 Throttle Actuator Control Motor Circuit Low (+ P2103) (from Aug 2009) →