2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010


CHECK MAIN BODY ECU
B136051E01
B136052E01
  1. Disconnect the 1A, 1B, 1E, and 1H main body ECU connectors.

  2. Measure the voltages and resistances of the wire harness side connectors.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND1 (1H-2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    BECU (1B-4) - Body ground
    W-R - Body ground
    Power source circuit (From battery)
    Always
    11 to 14 V
    BDR1 (1E-9) - Body ground
    B-Y - Body ground
    Power source circuit (From battery)
    Always
    11 to 14 V
    GND1,2 (1H-2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the main body ECU connectors.

  4. Measure the voltages of the wire harness side connectors.

Standard voltage: 
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
WMTR (1B-1) - GND1,2 (1H-2)
B-O - W-B
Rear washer motor output
Rear washer motor OFF
Below 1 V
Rear washer motor ON
10 to 14 V
SIG (1F-8) - GND1,2 (1H-2)
B-R - W-B
ECU power supply (from ignition switch)
Ignition switch OFF
Below 1 V
Ignition switch ON
10 to 14 V
MPX2 (E6-23) - GND1, 2 (1H-2)
BR-R - W-B
Multiplex communication signal
Ignition switch ON
Signal waveform
WRIN (E8-9) - GND1, 2 (1H-2)
BR-W - W-B
Rear wiper switch signal
Ignition switch ON and rear wiper switch OFF
10 to 14 V
Ignition switch ON and wiper switch LO
Below 1 V
WRLO (E8-10) - GND1, 2 (1H-2)
GR-R - W-B
Rear wiper switch signal
Ignition switch ON and rear wiper switch OFF
10 to 14 V
Ignition switch ON and rear wiper switch HI
Below 1 V
RWSW (E7-1) - GND1, 2 (1H-2)
LG-B - W-B
Rear washer switch signal
Ignition switch ON and rear washer switch OFF
10 to 14 V
Ignition switch ON and rear washer switch ON
Below 1 V
If the result is not as specified, there may be a malfunction on the wire harness side.

CHECK BACK DOOR ECU
If the result is not as specified, there may be a malfunction on the wire harness side.
B062706E01
  1. Disconnect the S2 back door ECU connector.

  2. Measure the voltages and resistances of the wire harness side connectors.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    BECU (S2-5) - Body ground
    W-R - Body ground
    Power source circuit (From battery)
    Always
    11 to 14 V
    GND (S2-3) - Body ground)
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the back door ECU connector.

  4. Measure the voltages of the wire harness side connectors.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    BDR (S2-4) - GND (S2-3)
    L-O - W-B
    Power supply (from battery)
    Always
    11 to 14 V
    SIG (S2-6) - GND (S2-3)
    B-R - W-B
    ECU power supply (from ignition switch)
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    11 to 14 V
    WIP- (S5-1) - GND (S2-3)
    R-G - W-B
    Rear wiper motor output
    Ignition switch ON and wiper switch LO or HI
    Pulse generation
    WIP+ (S5-2) - GND (S2-3)
    Y-G - W-B
    Rear wiper motor output
    Ignition switch ON and wiper switch LO or HI
    Pulse generation
    W (S5-3) - GND (S2-3)
    BR-B - W-B
    Rear wiper reverse position switch signal
    Ignition switch ON
    Pulse generation
    P (S5-12) - E (S2-19)
    P-B - V-G
    Rear wiper housing position switch signal
    Ignition switch ON
    Below 1 V
    GCTY (S5-10) - GND (S2-3)
    B-O - W-B
    Back window door courtesy switch signal
    Back window door closed
    11 to 14 V
    Back window door open
    Below 1 V
    MPX2 (S2-1) - GND (S2- 3)
    BR-R - W-B
    Multiplex communication signal circuit
    During communication
    Signal waveform
    If the result is not as specified, there may be a malfunction on the wire harness side.

← PROBLEM SYMPTOMS TABLE (from Aug 2011)TERMINALS OF ECU (from Nov 2010) →