2011-2016 FJ Cruiser · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jul 2007 – Jul 2009


1. INSTALL IGNITION COIL ASSEMBLY

A126385E01
  1. For Bank 1:

    1. Install the 3 ignition coils with the 3 bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7.4 ft.*lbf }

    2. Connect the 3 ignition coil connectors.

  1. A126386E01
    For Bank 2:

    1. Install the 3 ignition coils with the 3 bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7.4 ft.*lbf }

    2. Connect the 3 ignition coil connectors.


2. CONNECT VENTILATION HOSE

A075645E01
  1. Connect the ventilation hose to the intake air surge tank.


3. INSTALL NO. 1 SURGE TANK STAY

  1. A126389
    Install the No. 1 surge tank stay with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


4. INSTALL OIL BAFFLE PLATE

  1. A126390
    Install the oil baffle plate with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


5. INSTALL AIR CLEANER ASSEMBLY

  1. A075596E01
    Install the air cleaner onto the throttle body.

  1. Connect the air cleaner hose to the air cleaner.

  1. Install the air cleaner with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A075595E01
    Connect the mass air flow meter connector.

  1. Engage the 2 wire harness clamps.

  1. Connect the vacuum hose.

  1. A075594E01
    Connect the No. 2 ventilation hose.


6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }


7. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all the electrical systems OFF.
  2. Conduct the inspection when the cooling fan motor is turned OFF.

  1. Warm up the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Select the following menu items: Powertrain / Engine and ECT / Date List / IGN Advance.

    3. Inspect the ignition timing during idling.

      Ignition timing:
      7 to 24°CA BTDC during idling (Transmission in neutral position)

    4. Check that the ignition timing advances immediately when the engine speed is increased.

  1. A118802E01
    When not using intelligent tester:

    1. Using SST, connect the terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Do not connect the terminals incorrectly as it causes breakage of the engine.

    2. Remove the air cleaner.

    3. A076315E02
      Pull out the wire harness shown in the illustration.

    4. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      1. Use timing light that detects the first signal.
      1. After checking, wrap the wire harness with tape.

    5. A076316E01
      Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12°CA BTDC during idling (Transmission in neutral position)

    6. Remove SST from the DLC3.

    7. Inspect the ignition timing during idling.

      Ignition timing:
      7 to 24°CA BTDC during idling (Transmission in neutral position)

    8. Install the air cleaner.


8. INSPECT ENGINE IDLING SPEED

NOTICE:
  1. Turn all the electrical systems OFF.
  2. Operate the inspection when the cooling fan motor is turned OFF.

  1. Warm up the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Select the following menu items: Powertrain / Engine and ECT / Date List / Engine Speed.

    3. Inspect the engine idling speed.

      Idling speed:
      650 to 750 rpm (Transmission in neutral position)

  1. A118802E02
    When not using the intelligent tester:

    1. Using SST, connect the terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Race the engine speed at 2500 rpm for approximately 90 seconds.

    3. Inspect the engine idling speed.

      Idling speed:
      650 to 750 rpm (Transmission in neutral position)


9. INSTALL V-BANK COVER

  1. A126475
    Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

← REMOVAL (Jul 2007 – Jul 2009)PARTS LOCATION (Jul 2007 – Jul 2009) →