2011-2016 FJ Cruiser · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE WINDSHIELD WIPER ARM COVER

  1. E127858E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 3 front wiper arm cover.


3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E127859
    Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE)

HINT:
Use the same procedure as for the LH side.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


6. REMOVE ROOF ANTENNA POLE SUB-ASSEMBLY

B135011
  1. Remove the radio antenna pole by turning it in the direction of the arrow shown in the illustration.


7. REMOVE ANTENNA ORNAMENT

  1. E127861E01
    Pull out the antenna ornament vertically.


8. REMOVE FRONT FENDER SIDE PANEL UPPER RH

  1. B210064
    Disengage the 4 clips and remove the front fender side panel upper RH.

  1. Remove the 4 clips from the front fender side panel upper RH.


9. REMOVE FRONT FENDER SIDE PANEL UPPER LH

  1. B210065
    Disengage the 4 clips and remove the front fender side panel upper LH.

  1. Remove the 4 clips from the front fender side panel upper LH.


10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E127863
    Disengage the 7 clips and remove the cowl top ventilator louver sub-assembly.


11. REMOVE COWL TOP VENTILATOR LOUVER RH

  1. E127864
    Disengage the clip and remove the hood to cowl top seal.

  1. Remove the 3 clips and the claw, and remove the cowl top ventilator louver RH.


12. REMOVE COWL TOP VENTILATOR LOUVER LH

  1. E127865
    Remove the 5 clips.

  1. Disengage the 7 claws and remove the cowl top ventilator louver LH.


13. REMOVE FRONT DOOR SCUFF PLATE RH

  1. B130597
    Disengage the 14 claws and remove the front door scuff plate.


14. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


15. REMOVE ACCESS DOOR SCUFF PLATE RH

  1. B130598
    Disengage the 6 claws and remove the access door scuff plate.


16. REMOVE ACCESS DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


17. REMOVE FRONT FLOOR FOOTREST

  1. B130586
    Disengage the 4 claws and remove the front floor footrest.


18. REMOVE FOOTREST CLIP

  1. B130587
    Remove the 2 footrest clips.


19. REMOVE COWL SIDE TRIM BOARD RH

  1. B130599
    Remove the clip.

  1. Disengage the 2 claws and remove the cowl side trim board.


20. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


21. REMOVE ROOF SIDE INNER GARNISH COVER RH

B130600E01

HINT:
Use the same procedure for both sides.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the roof side inner garnish cover.


22. REMOVE ROOF SIDE INNER GARNISH COVER LH

HINT:
Use the same procedure as for the RH side.


23. REMOVE ROOF SIDE RAIL GARNISH RH

  1. B130602
    Remove the 2 bolts.

  1. Disengage the 2 claws and remove the roof side rail garnish.


24. REMOVE ROOF SIDE RAIL GARNISH LH

HINT:
Use the same procedure as for the RH side.


25. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B130603
    Remove the front door opening trim weatherstrip.


26. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


27. REMOVE ASSIST GRIP PLUG

B175647E01

HINT:
Use the same procedure to remove all the assist grip plugs.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.


28. REMOVE ASSIST GRIP ASSEMBLY

B175648E01

HINT:
Use the same procedure to remove all the assist grips.

  1. Remove the 2 screws and the assist grip.


29. REMOVE VISOR SUB-ASSEMBLY RH

B177923E01
  1. Disengage the 2 claws and remove the visor sub-assembly.


30. REMOVE VISOR SUB-ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


31. REMOVE FRONT PILLAR GARNISH RH

  1. B130608
    Disengage the 2 clips and the claw and remove the front pillar garnish.


32. REMOVE FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.


33. REMOVE VISOR ASSEMBLY RH

  1. B130629
    Remove the visor support shaft from the visor holder.

  1. Remove the 2 screws and the visor.


34. REMOVE VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


35. REMOVE VISOR HOLDER

B130630E02

HINT:
Use the same procedure for both sides.

  1. Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.

    HINT:
    The claw may be damaged during removal. However, it is reusable because this does not effect its function.


36. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER

B135952
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the inner rear view mirror stay holder cover.


37. REMOVE INNER REAR VIEW MIRROR ASSEMBLY

B135954
  1. Remove the 2 screws and remove the inner rear view mirror.


38. REMOVE ROOM LIGHT ASSEMBLY

E114441E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.

  1. B124365E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 covers.

  1. E114442E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.

  1. B138413E01
    Disengage the roof wire from the claw of the room light.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.

  1. Remove room light bulb No. 1.


39. REMOVE ROOF HEADLINING

HINT:
It is not necessary to remove the roof headlining completely. Slightly lower the front section of the roof headlining.


40. REMOVE WINDSHIELD OUTSIDE UPPER MOULDING SUB-ASSEMBLY

  1. B135038E01
    Apply protective tape to the roof panel in the area around the windshield outside upper moulding.

  1. B200653
    Insert the piano wires between the vehicle body and the windshield outside upper moulding, as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

    NOTICE:
    When separating the windshield outside upper moulding from the vehicle, do not damage the vehicle's paintwork or exterior ornaments.

  1. B135039
    Disengage the 6 claws and the 2 clips and remove the windshield outside upper moulding.


41. REMOVE ROOF DRIP SIDE FINISH MOULDING RETAINER

B135040

HINT:
Use the same procedure to remove all the roof drip side finish moulding retainers.

  1. Remove the screw and the roof drip side finish moulding retainer.


42. REMOVE FRONT PILLAR OUTER GARNISH

  1. B135013
    Remove the nut.

  1. Disengage the 5 clips and remove the front pillar outer garnish.


43. REMOVE ROOF SIDE GARNISH PROTECTOR

  1. B135014E01
    Using a clip remover, remove the 4 clips.

  1. Remove the 3 pieces of double-sided adhesive tape and the roof side garnish protector.


44. REMOVE WINDSHIELD OUTSIDE LOWER MOULDING

B139388E01
  1. Apply protective tape to the outer circumference of the windshield glass, as shown in the illustration.

  1. B139389
    Disengage the 6 claws and remove the windshield outside lower moulding.


45. REMOVE WINDSHIELD OUTSIDE MOULDING

B139387E01
  1. Using a knife, cut off the windshield outside moulding, as shown in the illustration.

    NOTICE:
    Do not damage the vehicle body with the knife.

  1. Remove the windshield outside moulding.

    HINT:
    Make a partial cut in the windshield outside moulding. Then pull and remove it by hand.


46. REMOVE WINDSHIELD GLASS

B139390E01
  1. Apply protective tape to the outer circumference of the windshield glass, as shown in the illustration.

  1. From the interior, insert piano wires between the vehicle body and the windshield glass, as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

    NOTICE:
    1. When separating the windshield glass from the vehicle, do not damage the vehicle's paintwork or exterior/interior ornaments.
    2. To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.

  1. B139391E01
    Place matchmarks on the windshield glass and vehicle body in the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed unless the windshield glass is going to be reused.

  1. Cut through the adhesive by pulling the piano wire around the windshield glass.

  1. B139392E01
    Disengage the 2 stoppers.

  1. Using suction cups, remove the windshield glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the windshield glass.

← COMPONENTS (from Aug 2012)REMOVAL (Nov 2010 – Jul 2011) →