REMOVAL
Removal / installation · Vehicles built Nov 2010 – Jul 2011
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012
| 1.
REMOVE WINDSHIELD WIPER ARM COVER
|
 |
- Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 3 front wiper arm cover.
| 2.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
|
 |
- Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
| 3.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE)
|
 |
- HINT:
- Use the same procedure as for the LH side.
| 4.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
|
 |
- HINT:
- Use the same procedure as for the LH side.
| 5.
REMOVE ROOF ANTENNA POLE SUB-ASSEMBLY
|
 |
Remove the radio antenna pole by turning it in the direction of the arrow shown in the illustration.
| 6.
REMOVE ANTENNA ORNAMENT
|
 |
- Pull out the antenna ornament vertically.
| 7.
REMOVE FRONT FENDER SIDE PANEL UPPER RH
|
 |
- Disengage the 4 clips and remove the front fender side panel upper RH.
Remove the 4 clips from the front fender side panel upper RH.
| 8.
REMOVE FRONT FENDER SIDE PANEL UPPER LH
|
 |
- Disengage the 4 clips and remove the front fender side panel upper LH.
Remove the 4 clips from the front fender side panel upper LH.
| 9.
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
|
 |
- Disengage the 7 clips and remove the cowl top ventilator louver sub-assembly.
| 10.
REMOVE COWL TOP VENTILATOR LOUVER RH
|
 |
- Disengage the clip and remove the hood to cowl top seal.
Remove the 3 clips and the claw, and remove the cowl top ventilator louver RH.
| 11.
REMOVE COWL TOP VENTILATOR LOUVER LH
|
 |
- Remove the 5 clips.
Disengage the 7 claws and remove the cowl top ventilator louver LH.
| 12.
REMOVE FRONT DOOR SCUFF PLATE RH
|
 |
- Disengage the 14 claws and remove the front door scuff plate.
| 13.
REMOVE FRONT DOOR SCUFF PLATE LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 14.
REMOVE ACCESS DOOR SCUFF PLATE RH
|
 |
- Disengage the 6 claws and remove the access door scuff plate.
| 15.
REMOVE ACCESS DOOR SCUFF PLATE LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 16.
REMOVE FRONT FLOOR FOOTREST (for LHD)
|
 |
- Disengage the 4 claws and remove the front floor footrest.
| 17.
REMOVE FOOTREST CLIP (for LHD)
|
 |
- Remove the 2 footrest clips.
| 18.
REMOVE COWL SIDE TRIM BOARD RH
|
 |
- Remove the clip.
Disengage the 2 claws and remove the cowl side trim board.
| 19.
REMOVE COWL SIDE TRIM BOARD LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 20.
REMOVE ROOF SIDE INNER GARNISH COVER RH
|
 |
- HINT:
- Use the same procedure for both sides.
Text in Illustration
*1
|
Protective Tape
|
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the roof side inner garnish cover.
| 21.
REMOVE ROOF SIDE INNER GARNISH COVER LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 22.
REMOVE ROOF SIDE RAIL GARNISH RH
|
 |
- Remove the 2 bolts.
Disengage the claw and the guide and remove the roof side rail garnish.
| 23.
REMOVE ROOF SIDE RAIL GARNISH LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 24.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
|
 |
- Remove the front door opening trim weatherstrip.
| 25.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 26.
REMOVE ASSIST GRIP PLUG
|
 |
- HINT:
- Use the same procedure to remove all the assist grip plugs.
Text in Illustration
*1
|
Protective Tape
|
*a
|
for RH Side
|
*b
|
for LH Side
|
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.
| 27.
REMOVE ASSIST GRIP ASSEMBLY
|
 |
- HINT:
- Use the same procedure to remove all the assist grips.
Text in Illustration
*a
|
for RH Side
|
*b
|
for LH Side
|
Remove the 2 screws and the assist grip.
| 28.
REMOVE VISOR SUB-ASSEMBLY RH
|
 |
- Disengage the 2 claws and remove the visor sub-assembly.
| 29.
REMOVE VISOR SUB-ASSEMBLY LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 30.
REMOVE FRONT PILLAR GARNISH RH
|
 |
w/ Assist Grip:
- Disengage the 2 clips and the guide and remove the front pillar garnish.
w/o Assist Grip:
- Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
Text in Illustration
*1
|
Protective Tape
|
- Remove the bolt.
Disengage the 2 clips and the guide and remove the front pillar garnish.
| 31.
REMOVE FRONT PILLAR GARNISH LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 32.
REMOVE VISOR ASSEMBLY RH
|
 |
- Remove the visor support shaft from the visor holder.
Remove the 2 screws and the visor.
| 33.
REMOVE VISOR ASSEMBLY LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 34.
REMOVE VISOR HOLDER
|
 |
- HINT:
- Use the same procedure for both sides.
Text in Illustration
*a
|
for RH Side
|
*b
|
for LH Side
|
Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.
- HINT:
- The claw may be damaged during removal. However, it is reusable because this does not effect its function.
| 35.
REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror) |
 |
(Click here)
| 36.
REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror) |
 |
(Click here)
| 37.
REMOVE ROOM LIGHT ASSEMBLY
|
 |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.
- Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 covers.
- Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.
- Disengage the roof wire from the claw of the room light.
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.
Remove room light bulb No. 1.
| 38.
REMOVE ROOF HEADLINING |
 |
- HINT:
- It is not necessary to remove the roof headlining completely. Slightly lower the front section of the roof headlining.
| 39.
REMOVE WINDSHIELD OUTSIDE UPPER MOULDING SUB-ASSEMBLY
|
 |
- Apply protective tape to the roof panel in the area around the windshield outside upper moulding.
Text in Illustration
*1
|
Protective Tape
|
- Insert the piano wires between the vehicle body and the windshield outside upper moulding, as shown in the illustration.
Text in Illustration
*1
|
Wooden Block
|
Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.
- NOTICE:
- When separating the windshield outside upper moulding from the vehicle, do not damage the vehicle's paintwork or exterior ornaments.
- Disengage the 4 claws and the 2 clips and remove the windshield outside upper moulding.
| 40.
REMOVE ROOF DRIP SIDE FINISH MOULDING RETAINER
|
 |
- HINT:
- Use the same procedure to remove all the roof drip side finish moulding retainers.
Remove the screw and the roof drip side finish moulding retainer.
| 41.
REMOVE FRONT PILLAR OUTER GARNISH LH
|
 |
- Remove the nut.
Disengage the 5 clips and remove the front pillar outer garnish.
| 42.
REMOVE FRONT PILLAR OUTER GARNISH RH |
 |
- HINT:
- Use the same procedure as for the LH side (Click here).
| 43.
REMOVE NO. 2 ROOF SIDE GARNISH PROTECTOR
|
 |
- Using a clip remover, remove the 4 clips.
Text in Illustration
*1
|
Double-sided Adhesive Tape
|
Remove the 3 pieces of double-sided adhesive tape and the roof side garnish protector.
| 44.
REMOVE NO. 1 ROOF SIDE GARNISH PROTECTOR |
 |
- HINT:
- Use the same procedure as for the No. 2 roof side garnish protector (Click here).
| 45.
REMOVE WINDSHIELD OUTSIDE LOWER MOULDING |
 |
- Apply protective tape to the outer circumference of the windshield glass, as shown in the illustration.
Text in Illustration
*1
|
Protective Tape
|
- Disengage the 6 claws and remove the windshield outside lower moulding.
| 46.
REMOVE WINDSHIELD OUTSIDE MOULDING LH |
 |
- Using a knife, cut off the windshield outside moulding, as shown in the illustration.
Text in Illustration
*A
|
w/o Rain G
|
*B
|
w/ Rain G
|
*a
|
Cut
|
- NOTICE:
- Do not damage the vehicle body with the knife.
Remove the windshield outside moulding.
- HINT:
- Make a partial cut in the windshield outside moulding. Then pull and remove it by hand.
| 47.
REMOVE WINDSHIELD OUTSIDE MOULDING RH |
 |
- HINT:
- Use the same procedure as for the LH side.
| 48.
REMOVE WINDSHIELD GLASS |
 |
- Apply protective tape to the outer circumference of the windshield glass, as shown in the illustration.
Text in Illustration
*1
|
Plastic Sheet
|
*2
|
Protective Tape
|
*3
|
Piano Wire
|
*4
|
Stopper
|
From the interior, insert piano wires between the vehicle body and the windshield glass, as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.
- NOTICE:
- When separating the windshield glass from the vehicle, do not damage the vehicle's paintwork or exterior/interior ornaments.
- To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.
- Place matchmarks on the windshield glass and vehicle body in the locations indicated in the illustration.
Text in Illustration
*a
|
Matchmarks
|
- HINT:
- Matchmarks do not need to be placed unless the windshield glass is going to be reused.
Cut through the adhesive by pulling the piano wire around the windshield glass.
- Disengage the 2 stoppers.
Text in Illustration
*1
|
Stopper No. 1
|
*2
|
Stopper No. 2
|
Using suction cups, remove the windshield glass.
- NOTICE:
- Leave as much adhesive on the vehicle body as possible when removing the windshield glass.