2011-2016 FJ Cruiser · Service Manual ENGINE

P0230 Fuel Pump Primary Circuit

Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Nov 2010 – Jul 2012 Aug 2012 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014

DESCRIPTION

As shown in the illustration, when the engine is cranked, current flows from terminal ST1 of the ignition switch into the ECM and the ST (starter) relay coil.
When the STA signal and NE signal are input to the ECM, Tr1 (power transistor 1) is turned ON, current flows to the coil of the circuit opening relay, the relay switches on, power is supplied to the fuel pump, and the fuel pump operates.
While the NE signal is generated (engine running), the ECM keeps the Tr1 ON (circuit opening relay ON) and the fuel pump also keeps operating.
The fuel pump speed is controlled at two levels (high speed or low speed) by engine condition (starting, light load, heavy load). When the engine starts (STA ON), Tr2 (power transistor 2) in the ECM is OFF, so the fuel pump relay closes and positive battery voltage is applied directly to the fuel pump. The fuel pump operates at high speed.
During idling or under light loads, Tr2 goes ON, and then power is supplied to the fuel pump via the fuel pump resistor. The fuel pump operates at low speed.
A175160E01
DTC No.
DTC Detection Conditions
Trouble Areas
P0230
Open or short in fuel pump relay circuit
(1 trip detection logic)
  1. Open or short in fuel pump relay circuit
  2. Fuel pump relay
  3. ECM

WIRING DIAGRAM

A133414E02

INSPECTION PROCEDURE

HINT:
  1. This DTC chart is on the premise that the engine is started normally. If the engine is difficult to start, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. INSPECT ECM (FPR VOLTAGE)
A115970E09
  1. Measure the voltage between the terminals of the B3 ECM connector.

    Standard Voltage:
    Tester Connections
    Conditions
    Specified Conditions
    FPR (B3-30) - E1 (B3-1)
    STA signal ON
    11 to 14 V
    STA signal OFF (engine idling)
    0 to 3 V



NG
Go to step 2
OK

REPLACE ECM (Click here)

2. INSPECT FUEL PUMP RELAY ASSEMBLY
A030519E02
  1. Remove the fuel pump relay from the engine room relay block.

  1. Check the fuel pump relay resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    3 - 4
    Below 1 Ω
    3 - 5
    10 kΩ or higher
    3 - 4
    10 kΩ or higher
    (when battery voltage applied to terminals 1 and 2)
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminals 1 and 2)

  1. Reinstall the fuel pump relay.



NG
REPLACE FUEL PUMP RELAY ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (FUEL PUMP RELAY - ECM)
A133446E03
  1. Remove the fuel pump relay from the engine room relay block.

  1. Disconnect the B3 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    Fuel pump relay (1) - FPR (B3-30)
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    Fuel pump relay (1) or FPR (B3-30) - Body ground
    10 kΩ or higher

  1. Reinstall the fuel pump relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0230 Fuel Pump Primary Circuit (Jul 2007 – Nov 2007)P0230 Fuel Pump Primary Circuit (Nov 2010 – Jul 2012) →