2011-2016 FJ Cruiser · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

HINT:
The procedure described below is for the LH side. Use the same procedure for both the LH and RH sides, unless otherwise specified.


1. PRECAUTION

CAUTION:
Read "PRECAUTION" thoroughly before servicing (Click here).


2. INSTALL REAR AIRBAG SENSOR
  1. Check that the ignition switch is turned to OFF.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.

  1. C128268E02
    Connect the connector to the rear airbag sensor.
    Text in Illustration 
    *1
    Outer Housing

  1. C128266
    Install the rear airbag sensor with the nut.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    CAUTION:
    1. If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the rear airbag sensor, make sure that the SRS wiring does not interfere with any other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the rear airbag sensor.


3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
  1. Engage the 6 clips and the 8 claws and install the deck trim side panel.

  1. Tighten the 3 screws.


4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Engage the 6 clips and the 8 claws and install the deck trim side panel.

  1. Tighten the 3 screws.

  1. Tighten the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


5. INSTALL REAR SEAT OUTER BELT ASSEMBLY

HINT:
Use the same procedure as for the RH side.


6. INSTALL LAP BELT OUTER ANCHOR COVER

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the lap belt outer anchor cover.


7. INSTALL QUARTER TRIM POCKET (w/o Woofer)
  1. Engage the 6 claws and install the quarter trim pocket.


8. INSTALL SIDE TRIM COVER (w/o Woofer)
  1. Engage the 6 claws and the 2 guides and install the side trim cover.


9. INSTALL QUARTER TRIM POCKET TRAY (w/o Woofer)
  1. Engage the 7 claws and install the quarter trim pocket tray.


10. INSTALL PACKAGE HOLDER NET HOOK (w/o Woofer)

HINT:
Use the same procedure to install all the package holder net hooks.

  1. Install the package holder net hook with the bolt.

    Torque:
    8.1 N*m{ 83 kgf*cm , 72 in.*lbf }


11. INSTALL AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)
  1. Install the amplifier box speaker with the 4 screws.

    Torque:
    8.1 N*m{ 83 kgf*cm , 72 in.*lbf }

  1. Connect the connectors.


12. INSTALL SPEAKER MOUNTING COVER (w/ Woofer)
  1. Engage the 8 clips and 2 guides and install the speaker mounting cover.


13. INSTALL DECK SIDE GARNISH (w/ Woofer)
  1. Engage the 6 claws and install the deck side garnish.


14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:
Use the same procedure as for the RH side.


15. INSTALL ACCESS DOOR SCUFF PLATE

HINT:
Use the same procedure as for the RH side.


16. INSTALL FRONT DOOR SCUFF PLATE

HINT:
Use the same procedure as for the RH side.


17. INSTALL REAR FLOOR MAT ASSEMBLY
  1. Install the rear floor mat with the 2 clips.


18. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

HINT:
Use the same procedure for both sides.

  1. Install the luggage hold belt striker with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the cap.


19. INSTALL REAR FLOOR MAT SUPPORT PLATE
  1. Engage the 11 claws and install the rear floor mat support plate.

  1. Tighten the 5 screws.


20. INSTALL REAR FLOOR BOARD
  1. Engage the clip and claw and install the rear floor board.

  1. B135074E05
    Install the luggage hold belt striker with the bolt.
    Text in Illustration 
    *1
    Guide
    *a
    for RH Side
    *b
    for LH Side

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Use the same procedure for both sides.


21. INSTALL REAR SEATBACK ASSEMBLY LH (for LH Side)

  1. B130721E01
    Engage the hook and temporarily install the rear seatback with the 2 bolts.

  1. Tighten the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Install the rear center seat inner belt into the rear seatback holder.


22. INSTALL REAR SEATBACK ASSEMBLY RH (for RH Side)

  1. B130750E01
    Engage the hook and temporarily install the rear seatback with the 2 bolts.

  1. Tighten the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Pull up the rear seatback.

  1. B135128E01
    Install the rear seat inner belt into the rear seatback holder.

  1. Install the anchor plate of the rear center seat outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the anchor plate over the convex area of the rear seat inner belt.


23. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH (for LH Side)

  1. B130720
    Engage the 8 clips and install the rear seatback board carpet.

  1. Pull up the rear seatback.


24. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH (for RH Side)

  1. B130749
    Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Engage the 10 clips and install the rear seatback board carpet.

  1. Pull up the rear seatback.


25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


26. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    HINT:
    Some systems need initialization when disconnecting the cable from the negative battery terminal.


27. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).

← INSTALLATION (Jul 2007 – Oct 2010)INSTALLATION (from Aug 2012) →