2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Line for Short to +B

Circuit diagnosis · Vehicles built Aug 2009 – Oct 2010

DESCRIPTION

A short to +B is suspected in the CAN bus line when there is continuity between terminals 16 (BAT) and 6 (CANH) or terminals 16 (BAT) and 14 (CANL) of the DLC3.
Symptom
Trouble Area
There is continuity between terminals 16 (BAT) and 6 (CANH) or 16 (BAT) and 14 (CANL) of the DLC3.
  1. Short to +B in CAN bus line
  2. ECM
  3. Master cylinder solenoid (skid control ECU)
  4. Yaw rate sensor
  5. Steering angle sensor
  6. CAN junction connector

WIRING DIAGRAM

C134964E02

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS LINE FOR SHORT TO +B (DLC3 BRANCH WIRE)

  1. C133849E06
    Turn the ignition switch off.

  1. Disconnect the E63 DLC3 branch wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to CAN Junction Connector "A" Side (w/ Ground Terminal))

  1. C118856E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


2. CONNECT CONNECTOR
  1. Reconnect the DLC3 branch wire connector.


NEXT


3. CHECK CAN BUS LINE FOR SHORT TO +B (SKID CONTROL ECU BRANCH WIRE)

  1. C133850E02
    Turn the ignition switch off.

  1. Disconnect the E66 skid control ECU branch wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to CAN Junction Connector "B" Side (w/o Ground Terminal))

  1. C118856E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more

    Text in Illustration 
    *1
    DLC3



NG
Go to step 6
OK


4. CONNECT CONNECTOR
  1. Reconnect the skid control ECU branch wire connector.


NEXT


5. CHECK CAN BUS LINE FOR SHORT TO +B (SKID CONTROL ECU BRANCH WIRE)

  1. E192054E01
    Turn the ignition switch off.

  1. Disconnect the A4 skid control ECU connector.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Skid Control ECU)

  1. C118856E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE SKID CONTROL ECU BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID

6. CONNECT CONNECTOR
  1. Reconnect the skid control ECU branch wire connector.


NEXT


7. CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR BRANCH WIRE)

  1. C133849E08
    Turn the ignition switch off.

  1. Disconnect the E65 yaw rate sensor branch wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to CAN Junction Connector "A" Side (w/ Ground Terminal))

  1. C118856E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more

    Text in Illustration 
    *1
    DLC3



NG
Go to step 10
OK


8. CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor branch wire connector.


NEXT


9. CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR BRANCH WIRE)

  1. E192055E01
    Turn the ignition switch off.

  1. Disconnect the E34 yaw rate sensor connector.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Yaw Rate Sensor)

  1. C118856E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE SENSOR (Click here)

10. CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor branch wire connector.


NEXT


11. CHECK CAN BUS LINE FOR SHORT TO +B (STEERING ANGLE SENSOR BRANCH WIRE)

  1. C133849E07
    Turn the ignition switch off.

  1. Disconnect the E64 steering angle sensor branch wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to CAN Junction Connector "A" Side (w/ Ground Terminal))

  1. C118856E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more

    Text in Illustration 
    *1
    DLC3



NG
Go to step 14
OK


12. CONNECT CONNECTOR
  1. Reconnect the steering angle sensor branch wire connector.


NEXT


13. CHECK CAN BUS LINE FOR SHORT TO +B (STEERING ANGLE SENSOR BRANCH WIRE)

  1. E192056E01
    Turn the ignition switch off.

  1. Disconnect the E16 steering angle sensor connector.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Steering Angle Sensor)

  1. C118856E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)

14. CONNECT CONNECTOR
  1. Reconnect the steering angle sensor branch wire connector.


NEXT


15. CHECK CAN BUS LINE FOR SHORT TO +B (ECM MAIN WIRE)

  1. C133849E05
    Turn the ignition switch off.

  1. Disconnect the E62 ECM main wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to CAN Junction Connector "A" Side (w/ Ground Terminal))

  1. C118856E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more

    Text in Illustration 
    *1
    DLC3



NG
REPLACE CAN JUNCTION CONNECTOR
OK


16. CONNECT CONNECTOR
  1. Reconnect the ECM main wire connector.


NEXT


17. CHECK CAN BUS LINE FOR SHORT TO +B (ECM MAIN WIRE)

  1. E192053E01
    Turn the ignition switch off.

  1. Disconnect the E81 ECM connector.

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to ECM)

  1. C118856E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or more

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CAN-H, CAN-L)
OK

REPLACE ECM (Click here)


← Check CAN Bus Lines for Short Circuit (RHD Models) (from Aug 2012)Check CAN Bus Line for Short to GND (Aug 2009 – Oct 2010) →