2011-2016 FJ Cruiser · Service Manual HEATER & AIR CONDITIONING SYSTEM

INSTALLATION

Removal / installation · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 from Aug 2013


1. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY

I102450
  1. Engage the 4 claws and install the lower defroster nozzle.


2. INSTALL HEATER TO REGISTER DUCT ASSEMBLY

I102449
  1. Engage the 4 claws and install the heater to register duct.


3. INSTALL AIR CONDITIONING UNIT ASSEMBLY

I102446
  1. Install the air conditioning unit with the 2 screws as shown in the illustration.


4. INSTALL INSTRUMENT PANEL REINFORCEMENT
  1. Provisionally install the air conditioning unit assembly.

  1. Insert the bracket hook into the holes of the reinforcement bracket, and provisionally install the reinforcement.

  1. Install the instrument panel reinforcement with the 7 bolts.

  1. Install the 2 caps.

    I102444

  1. Install the 5 bolts.

    NOTICE:
    Tighten the bolts in the sequence order shown in the illustration to install the air conditioner unit assembly.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt

  1. Install the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf } for nut


    I102442E01

  1. Engage the clamps.

    I102441

  1. Connect the connectors.

  1. Connect the wire harness with the 3 bolts and 5 nuts.

    I102440

    Torque:
    7.3 N*m{ 74 kgf*cm , 65 in.*lbf } for nut


5. INSTALL COOLER UNIT DRAIN HOSE

  1. I102468
    Install the cooler unit drain hose.


6. INSTALL MAIN BODY ECU (DRIVER SIDE J/B)

  1. I102439
    Install the main body ECU with the 2 nuts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


7. INSTALL INSTRUMENT PANEL SIDE BRACKET

  1. I102438
    Install the instrument panel side bracket with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


8. INSTALL STEERING COLUMN ASSEMBLY

C133810
  1. Install the steering column assembly with the 4 nuts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Connect each of the connectors to the steering column assembly.

  1. Connect the wire harness clamps to the steering column assembly.

    CAUTION:
    Use a shop rag or piece of cloth to wipe any dirt off the installation plane and column body side.

    NOTICE:
    Be careful not to scratch or soil the installation plane of the steering column.


9. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

I102502E01
  1. Align the matchmarks on the steering column assembly and the steering intermediate shaft assembly.

  1. Install the steering intermediate shaft assembly and thrust stopper onto the steering column assembly with the bolt.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }


10. INSTALL STEERING COLUMN HOLE COVER

F051329
  1. Install the steering column hole cover with the 4 clips.

    NOTICE:
    Be careful not to damage the dust seal of the steering column hole cover.


11. INSTALL ECM
  1. Install the ECM with the 3 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the 6 connectors.


12. INSTALL NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET

I102436
  1. for LH side:

    1. Install the instrument panel brace mounting bracket with the bolt and nut.

  1. I102437
    for RH side:

    1. Install the instrument panel brace mounting bracket with the bolt and nut.


13. INSTALL NO. 1 AIR DUCT

I102434
  1. Engage the 3 claws and install the air duct.


14. INSTALL NO. 2 AIR DUCT

I102435
  1. Engage the 3 claws and install the air duct.


15. INSTALL REAR NO. 1 AIR DUCT

I102433
  1. Engage the 6 claws and 3 clamps and install the air duct.


16. INSTALL REAR NO. 2 AIR DUCT

I102432
  1. Engage the 6 claws and 3 clamps and install the air duct.


17. INSTALL NO. 1 HEATER TO REGISTER DUCT

I102430
  1. Install the heater to register duct with the screw.


18. INSTALL NO. 2 HEATER TO REGISTER DUCT

I102431
  1. Install the heater to register duct with the screw.


19. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY

B133866E01
  1. Install the lower instrument panel with the 2 <C> bolts, 2 <E> bolts, 7 <F> bolts and nut <G>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. Engage the clamps and connect the connectors.


20. CONNECT PASSENGER AIRBAG CONNECTOR

B133891
  1. Connect the passenger airbag connector.


21. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

  1. B133889
    Engage the 3 claws and install the instrument panel finish panel end.


22. INSTALL ASSIST GRIP RETAINER RH

  1. B133881
    Install the assist grip retainer with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


23. INSTALL ASSIST GRIP RETAINER LH

HINT:
Use the same procedure as for the RH side.


24. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

  1. B135134
    Connect the speaker connector.

  1. Insert the 2 hooks into the 2 instrument panel holes and install the front speaker bracket with the 2 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }


25. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

  1. B133865
    Engage the 4 clips and claw and install the instrument panel speaker panel.


26. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:
Use the same procedure as for the RH side.


27. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B176533E01
    Install the No. 2 instrument panel register assembly (Previous Version).

    1. Engage the 4 clips and 2 claws and install the instrument panel register.

    2. Install the clip.

  1. B188206E01
    Install the No. 2 instrument panel register assembly (New Version).

    1. Engage the 4 clips and 2 claws and install the instrument panel register.

    2. Install the bolt and clip.

    3. B188207E01
      Engage the 2 claws and install the instrument panel hole cover.


28. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH

  1. B133857
    Install the connectors to the instrument panel lower finish panel.

  1. Engage the claw and 2 clips and install the instrument panel lower finish panel.

  1. Install screw <A>.


29. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

  1. B133856
    Install the glove compartment door assembly with the 3 hinges while holding it horizontal.

  1. B133854E01
    Slightly flex the upper part of the glove compartment door assembly, and install the glove compartment door assembly.

  1. Install the glove compartment door stoppers onto the glove compartment door.


30. INSTALL COMBINATION METER ASSEMBLY

  1. B133863
    Connect the 2 connectors and the clamp.

  1. B133862
    Install the combination meter assembly with the 4 screws.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


31. INSTALL INSTRUMENT CLUSTER FINISH PANEL

B133861
  1. Connect the connectors.

  1. Engage the 3 clips and 4 claws and install the instrument cluster lower finish panel.


32. INSTALL LOWER INSTRUMENT PANEL LH

  1. B133864
    Install the lower instrument panel with the 4 <F> bolts.


33. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH

  1. B133860
    Engage the 5 clips and claw and install the lower instrument panel finish panel.

  1. Install the 2 <F> bolts.


34. INSTALL INSTRUMENT PANEL FINISH PLATE

E149563E01
  1. Install the instrument panel finish plate.


35. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

  1. B133859
    Engage the 3 claws and install the hood lock control lever.


36. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B133853
    Engage the 4 clips and 2 claws and install the instrument panel register.


37. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY

  1. B133852
    Engage the 3 clips and 2 claws and install the instrument lower cover.

  1. Install the 2 <F> bolts and 2 clips.


38. INSTALL CONSOLE UPPER PANEL NO. 1 GARNISH

B133902E01
  1. Slide the console upper panel garnish toward the front of the vehicle and engage claw B.

  1. Engage the claw A and clip and install the console upper panel garnish.


39. INSTALL FRONT CONSOLE BOX

  1. B133851
    Engage the 5 claws and install the front console box.

  1. Install the 4 <D> screws.


40. INSTALL BOX BOTTOM MAT

  1. B133899
    Install the box bottom mat.


41. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY

  1. B133897
    Engage the 3 claws and 5 clips and install the console upper rear panel.


42. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)

  1. B133894
    Install the shift lever knob.


43. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD)

  1. B133896
    Install the shift lever knob.


44. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY

B133901E01
  1. Slide the parking brake hole cover toward the rear of the vehicle and engage the 2 C claws.

  1. Engage the 4 claws and install the parking brake hole cover.


45. INSTALL RADIO RECEIVER ASSEMBLY

  1. B130576
    Connect the plug, the head unit connector and the 2 radio connectors.

  1. B138605
    Align the 2 bosses of the radio bracket with the hole in the instrument panel and install the radio receiver with the 4 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }


46. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY

B133888
  1. Connect the 3 connectors.

  1. Engage the 4 clips and install the integration control panel assembly.

  1. Install the 2 <H> screws.


47. INSTALL INSTRUMENT PANEL GARNISH LH

  1. B133886
    Engage the 3 clips and install the instrument panel garnish.

  1. Install 2 <H> screws.


48. INSTALL INSTRUMENT PANEL GARNISH RH

  1. B133887
    Engage the 3 clips and install the instrument panel garnish.

  1. Install screw <H>.


49. INSTALL FRONT PILLAR GARNISH RH

  1. B130608
    Engage the claw and the 2 clips and install the front pillar garnish.


50. INSTALL FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.


51. INSTALL ASSIST GRIP ASSEMBLY

B175648E01

HINT:
Use the same procedure to install all the assist grips.

  1. Install the assist grip with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


52. INSTALL ASSIST GRIP PLUG

B175649E01

HINT:
Use the same procedure to install all the assist grip plugs.

  1. Engage the 2 claws and install the assist grip plug.


53. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.


54. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.


55. INSTALL COWL SIDE TRIM BOARD RH

  1. B130599
    Engage the 2 claws and install the cowl side trim board.

  1. Install the clip.


56. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


57. INSTALL FOOTREST CLIP

B130588

HINT:
Use the same procedure for both sides.

  1. Engage the 2 claws and install the footrest clip.


58. INSTALL FRONT FLOOR FOOTREST

  1. B130589
    Engage the 2 studs and install the front floor footrest.


59. INSTALL FRONT DOOR SCUFF PLATE RH

  1. B130597
    Engage the 14 claws and install the door scuff plate.


60. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


61. INSTALL COMBINATION SWITCH ASSEMBLY

  1. C133809
    Install the 3 screws.

  1. Connect all connectors to the combination switch assembly.


62. INSTALL UPPER STEERING COLUMN COVER

  1. C133808
    Engage the claw and install the upper steering column cover.


63. INSTALL LOWER STEERING COLUMN COVER

  1. C133807
    Engage the 2 claws.

  1. Install the lower steering column cover with the 3 screws.


64. INSTALL STEERING WHEEL ASSEMBLY
  1. Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }


65. INSTALL STEERING PAD

  1. C128255E01
    Support the steering pad with one hand as shown in the illustration.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector.

  1. Confirm that the circumferencial groove of the "Torx" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. Using "Torx" socket wrench (T30), tighten the 2 "Torx" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

    NOTICE:
    Tighten the 2 bolts while holding the steering pad to prevent it from moving upward.


66. INSTALL LOWER NO. 2 STEERING WHEEL COVER

  1. C128196
    Install steering wheel cover lower No.2.


67. INSTALL LOWER NO. 3 STEERING WHEEL COVER

  1. C128196
    Install steering wheel cover lower No.2.


68. CONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)

I102429E01
  1. Install the heater water outlet hose onto the heater unit.

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle as shown in the illustration.


69. CONNECT HEATER WATER HOSE INLET

I102427E01
  1. Install the heater water inlet hose onto the heater unit.

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle as shown in the illustration.


70. INSTALL COOLER REFRIGERANT LIQUID PIPE A

I006878E06
  1. Remove the vinyl tape from liquid tube A and the connecting portion of the unit.

  1. Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the liquid pipe.

    Compressor oil:
    ND-OIL8 or the equivalent

  1. Install the O-ring onto the liquid pipe.

  1. Install the liquid and piping clamp.

    HINT:
    After connection, check the claw fitting of the piping clamp.


71. INSTALL COOLER REFRIGERANT SUCTION PIPE A

HINT:
Connection procedure of the suction pipe is the same as for the liquid pipe.


72. INSTALL COWL TOP VENTILATOR LOUVER LH

  1. E127865
    Install the cowl top ventilator louver LH with the 5 clips and engage the 7 claws.


73. INSTALL COWL TOP VENTILATOR LOUVER RH

  1. E127864
    Install the cowl top ventilator louver RH with the 3 clips and the claw.

  1. Install the hood to cowl top seal with the clip.


74. INSTALL COWL TOP VENTILATOR LOUVER ASSEMBLY

  1. E127863
    Install the cowl top ventilator louver sub-assembly with the 7 clips.


75. INSTALL FRONT FENDER SIDE PANEL UPPER LH
  1. Install the 4 new clips on the front fender side panel upper LH.

  1. B210065
    Engage the 4 clips and install the front fender side panel upper LH.


76. INSTALL FRONT FENDER SIDE PANEL UPPER RH
  1. Install the 4 new clips on the front fender side panel upper RH.

  1. B210064
    Engage the 4 clips and install the front fender side panel upper RH.


77. INSTALL ANTENNA ORNAMENT

  1. E127861E02
    Press in the antenna ornament in the direction shown in the illustration.


78. INSTALL ROOF ANTENNA POLE SUB-ASSEMBLY

B138406E01
  1. Install the radio antenna pole by turning it in the direction of the arrow shown in the illustration.

    Torque:
    3.3 N*m{ 35 kgf*cm , 29 in.*lbf }

    NOTICE:
    Use a short wrench, tighten with your finger, not your hand.


79. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E127876E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


80. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE)

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E127875E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


81. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E127874E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


82. INSTALL WINDSHIELD WIPER ARM COVER

  1. E127877E01
    Engage the claw and install the 3 front wiper arm cover.


83. ADD ENGINE COOLANT
  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    for Automatic Transmission
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    for Manual Transmission
    9.4 liters (9.9 US qts, 8.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. A220212E02
    Slowly pour coolant into the radiator reservoir until it reaches the Full line.
    Text in Illustration 
    *1
    FULL Line

  1. Install the reservoir cap.

  1. Install the radiator cap.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass, and then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3

  1. Repeat steps *1, *2 and *3 until the coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap.*4

  1. Set the air conditioning as follows.*5

    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the Full line.
    2. Do not start the engine when there is no coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap and check the coolant level.*7

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8

  1. A220212E02
    If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the Full line.
    If the coolant level is below the Full line, repeat steps *4 through *8.
    If the coolant level is above the Full line, drain coolant until the coolant level reaches the Full line.
    Text in Illustration 
    *1
    FULL Line


84. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }


85. CHECK SRS WARNING LIGHT
Click here

86. CHARGE REFRIGERANT

I100449E02

NOTICE:
Charge refrigerant in accordance with the equipment manual.

  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    Standard:
    570 to 630 g (20.11 to 22.22 oz.)

    NOTICE:
    1. Do not start the engine before charging it with refrigerant as the cooler compressor doesn't work properly without sufficient refrigerant. This could cause the compressor to overheat.
    2. Approximately 100 g (3.5 oz.) of refrigerant may need to be charged after bubbles disappear.
      The volume of refrigerant should be measured, not checked with the sight glass.

    HINT:

    1. The relationship between the refrigerant charge amount and the pressure is as follows.

      I104030E01
    2. High Charge Range:
      If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
    3. Low Charge Range:
      A shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises the refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and subsequent refrigerant leakage may occur.


    1. Install the caps onto the service valves on the refrigerant line.


87. WARM UP ENGINE

NOTICE:
Warm up the engine at less than 2,000 rpm for 1 minute or more after charging it with refrigerant.


88. CHECK FOR ENGINE COOLANT LEAK

CAUTION:
To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.

  1. Fill the radiator with engine coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. A220211E01
    Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
    Text in Illustration 
    *1
    Radiator Cap Tester


89. CHECK FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation as follows:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf*cm2, 57 to 85 psi)

    HINT:
    It is impossible for the above pressure to be maintained if there is leakage.

  1. I042222E14
    Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.

  1. I100587E03
    Bring the halogen leak detector close to the drain hose before performing the test.

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for at least 15 minutes.
    2. Place the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to the volatile gases.

    If such a reaction is unavoidable, the vehicle must be lifted up.

  1. If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.


90. POSITION FRONT WHEELS FACING STRAIGHT AHEAD
← INSTALLATION (Jul 2007 – Jul 2009)INSTALLATION (Nov 2010 – Jul 2013) →