2011-2016 FJ Cruiser · Service Manual HEATER & AIR CONDITIONING SYSTEM

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Jul 2007 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Switch A/C ON.

  1. Turn the blower switch to ON.

  1. Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.

  1. Stop the engine.

  1. Remove the caps from the service valves on the refrigerant line.

    I104027E01

  1. Connect the refrigerant recovery unit.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.

    NOTICE:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.


2. REMOVE RADIATOR GRILLE

  1. B134729
    Using a clip remover, remove the 2 clips.

  1. Remove the 2 screws.

  1. Disengage the 5 clips and remove the radiator grille.


3. REMOVE FRONT BUMPER ASSEMBLY

  1. B134730E02
    Apply protective tape as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape

  1. B138606
    Using a clip remover, remove the 5 clips.

  1. B134731
    Remove the 8 screws and 4 bolts.

  1. w/o Fog Light:

    1. B134733
      Disengage the 2 claws to remove the front bumper assembly.

  1. w/ Fog Light:

    1. Disengage the 2 claws and separate the front bumper assembly.

    2. Disconnect the connector to remove the front bumper assembly.

  1. B138601
    Remove the 4 clips.


4. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

I102481
  1. Remove the bolt to disconnect the discharge hose sub-assembly from the cooler condenser assembly.

  1. Remove the O-ring from the discharge hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.


5. DISCONNECT AIR CONDITIONING TUBE ASSEMBLY

I102482
  1. Remove the bolt to disconnect the air conditioning tube assembly from the cooler condenser assembly.

  1. Remove the O-ring from the air conditioning tube assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.


6. REMOVE COOLER BRACKET

I110527
  1. Remove the nut.

  1. Disengage the clamp to remove the cooler bracket.


7. REMOVE NO. 2 COOLER CONDENSER CUSHION LH

I102486
  1. Remove the 2 bolts and No. 2 cooler condenser cushion LH.


8. REMOVE NO. 2 COOLER CONDENSER CUSHION RH

I102484
  1. Remove the 2 bolts, nut and No. 2 cooler condenser cushion RH.


9. REMOVE COOLER CONDENSER ASSEMBLY

I109192
  1. Remove the 4 bolts and disengage the 2 hooks to remove the 2 No. 1 cooler condenser cushions.

    NOTICE:
    Hold the cooler condenser assembly by hand to prevent it from falling off when removing the cushion.

  1. Remove the cooler condenser assembly from the vehicle.

    NOTICE:
    Do not damage the cooler condenser assembly or radiator assembly when removing the cooler condenser assembly.

← REMOVAL (Aug 2013 – Jul 2014)DISASSEMBLY (from Jul 2007) →