2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1612/83 Lost Communication with Front Airbag Sensor RH

Diagnostic trouble codes · Vehicles built from Aug 2012

Also covers:

DESCRIPTION

The front airbag sensor RH circuit consists of the center airbag sensor assembly and front airbag sensor RH.
The front airbag sensor RH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag and pretensioner should be deployed.
These DTCs are stored when a malfunction is detected in the front airbag sensor RH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1612/83
B1613/83
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor RH circuit.
  2. Front airbag sensor RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor RH
  4. Center airbag sensor assembly

WIRING DIAGRAM

C267550E01

INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).


1. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)

  1. C267545E02
    Connect the connectors that link the engine room main wire and instrument panel wire.

  1. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-2 (+SR) - A40-1 (-SR)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Front Airbag Sensor RH)



NG
Go to step 7
OK


3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)
  1. Disconnect the service wire from connector B.

  1. C267546E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-2 (+SR) - Body ground
    Always
    1 MΩ or higher
    A40-1 (-SR) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor RH)



NG
Go to step 8
OK


4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)

  1. C267546E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-2 (+SR) - A40-1 (-SR)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor RH)



NG
Go to step 9
OK


5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)

  1. C267546E03
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A40-2 (+SR) - Body ground
    Ignition switch ON
    Below 1 V
    A40-1 (-SR) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor RH)



NG
Go to step 10
OK


6. CHECK FRONT AIRBAG SENSOR RH

  1. C267547E01
    Connect the connector to the center airbag sensor assembly.

  1. Interchange the front airbag sensor RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output.
    A
    DTC B1617/84 or B1618/84 is output.
    B
    DTC B1612/83 or B1613/83 is output.
    C

    HINT:
    Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the front airbag sensor RH and LH to their original positions and connect the connectors.

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Center Airbag Sensor Assembly



B
REPLACE FRONT AIRBAG SENSOR RH (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

7. CHECK INSTRUMENT PANEL WIRE (OPEN)

  1. C267548E02
    Disconnect the instrument panel wire connector from the engine room main wire.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EA5-2 (+SR) - EA5-1 (-SR)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE

8. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

  1. C267549E03
    Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EA5-2 (+SR) - Body ground
    Always
    1 MΩ or higher
    EA5-1 (-SR) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE

9. CHECK INSTRUMENT PANEL WIRE (SHORT)

  1. C267549E03
    Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EA5-2 (+SR) - EA5-1 (-SR)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE

10. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

  1. C267549E03
    Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    EA5-2 (+SR) - Body ground
    Ignition switch ON
    Below 1 V
    EA5-1 (-SR) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE


← B1610/13 Front Airbag Sensor RH Malfunction (from Nov 2010)B1615/14 Front Airbag Sensor LH Malfunction (Jul 2007 – Oct 2010) →