2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010


NOTICES WHEN CHECKING
  1. This wireless door lock control function operates only when the following 3 conditions are met:

    1. There is no key in the ignition key cylinder.

    2. All doors are closed.

    3. The power door lock system is operating normally.

      HINT:
      The unlock function operates even when a door is open.

  1. The size of the wireless door lock control operational area differs depending on the situation.

    1. The size of the operation area differs depending on the user and the way the transmitter is held.

    2. In certain areas, the remote control function will only operate partially for the operational area, which will be reduced due to the vehicle body shape and the influence of the surrounding environment.

    3. Since the transmitter uses weak radio waves, strong radio waves or electrical noise in the frequency used by the transmitter may reduce the size of the operational area and the remote control may not function.

    4. When the transmitter battery is weak, the size of the operational area is reduced and the remote control may not function.

      HINT:
      If the door control transmitter has been left in a place that is exposed to direct sunlight, such as on the instrument panel, it may cause the battery to be weakened or cause other related problems.


CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

HINT:
  1. The switches described in this text are the switches for transmitting signals. The switches are built into the door control transmitter.
  2. All the functions listed below must be checked in comparison with the remote control operational area.

  1. Make sure that the vehicle is in an area that allows the wireless control function to operate.

  1. Check basic functions.

    1. Check whether the LED of the transmitter comes on 3 times when each switch is pressed 3 times.

      HINT:
      If the LED does not come on when the switch has been pressed 3 times or more, it may have a weak battery.

    2. Check that all doors lock when LOCK switch is pressed.

    3. Check that the driver side door unlocks when the UNLOCK switch is pressed once, and it unlocks all doors when pressed twice within 3 seconds.

  1. Check the chattering prevention function.

    1. Check that the corresponding operation occurs only once and is not repeated continuously while the switch is held. However, when the switch is operated repeatedly at 1-second intervals, check that the corresponding operation is carried out.

  1. Check the switch operation fail-safe function.

    1. Check that the doors cannot be locked or unlocked by operating a switch on the unregistered transmitter, and that the doors are locked and unlocked by operating a switch on the registered transmitter.

  1. Check the answer-back function.

    1. When the LOCK switch is pressed, check that the hazard warning lights flash once and the wireless door lock buzzer sounds once*1 simultaneously with the locking operation.

    2. When the UNLOCK switch is pressed once, check that the hazard warning lights flash twice and the wireless door lock buzzer sounds twice*1 simultaneously with the unlocking operation.

      1. *1: w/ Wireless Door Lock Buzzer

  1. Check the automatic lock function.

    1. When all doors are unlocked with the UNLOCK switch and none of the doors are opened or locked within 30 seconds, check that the doors are relocked automatically.

  1. Check the illuminated entry function.

    HINT:
    Turn the room light switch to the DOOR position before the check.


    1. When all doors are locked and the UNLOCK switch is pressed, check that the interior lights and key illumination illuminates and all doors are unlocked.

  1. Check the door ajar warning function. (w/ Wireless Door Lock Buzzer)

    1. Check that the wireless door lock buzzer sounds for approximately 10 seconds when the LOCK switch is pressed with any of the doors ajar or open.

  1. Check the panic alarm function. (w/ Panic Alarm Function)

    1. Check that the horn sounds and the hazard warning lights for 30 seconds by the theft alarm function, when the PANIC switch is held down for 0.8 seconds or more. Also, check that the horn stops sounding and the lights stop flashing when any switch of the transmitter is pressed.

← ON-VEHICLE INSPECTION (Jul 2007 – Oct 2010)Only Wireless Control Function is Inoperative (Jul 2007 – Oct 2010) →