2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Only Wireless Control Function is Inoperative

Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher relay signals to the turn signal flasher relay (hazard warning lights).

WIRING DIAGRAM

B175113E01

INSPECTION PROCEDURE


1. CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch is operated, check that the locked doors unlock (Click here).

OK:
Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. CHECK KEY REMINDER WARNING SYSTEM
  1. Check that the key reminder buzzer operates normally (Click here).

    OK:
    Key reminder warning buzzer operates normally.



NG
GO TO KEY REMINDER WARNING SYSTEM (Click here)
OK


3. CHECK DOOR CONTROL TRANSMITTER MODULE
  1. When another registered door control transmitter is used, check that the wireless door lock function operates normally.

    OK:
    Wireless door control function operate normally.



NG
Go to step 6
OK


4. CHECK TRANSMITTER LED ILLUMINATION
  1. Check that the transmitter's LED illuminates 3 times when the switch is pressed 3 times.

    Result 
    Result
    Proceed to
    Transmitter's LED does not illuminate 3 times when switch is pressed 3 times
    A
    Transmitter's LED illuminates 3 times when switch is pressed 3 times
    B
    The transmitter's LED does not illuminate the second or third time
    C

    HINT:
    If the transmitter's LED does not illuminate the second or third time, replace the transmitter battery as it is depleted.



B
REPLACE DOOR CONTROL TRANSMITTER MODULE (Click here)

C
REPLACE TRANSMITTER BATTERY (Click here)
A


5. INSPECT TRANSMITTER BATTERY (VOLTAGE)
E114749E02
B194651E01
  1. Remove the battery from the door control transmitter module that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal (Click here).

  1. Install the previously removed transmitter battery.

  1. Using an oscilloscope, check the transmitter battery voltage waveform.

HINT:
When measuring the battery voltage, press one of the transmitter switches.

Standard Voltage:
Item
Content
Tester Connection
Battery positive (+) - Battery negative (-)
Tool Setting
0.5 V/DIV., 100 ms/DIV.
Condition
Press one of the transmitter switches
Specified Condition
2.2 to 3.2 V (Refer to the waveform)



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE DOOR CONTROL TRANSMITTER MODULE (Click here)

6. CHECK WAVE ENVIRONMENT
  1. Bring the transmitter near the door control receiver, and perform a wireless operation check.

    OK:
    Wireless functions operate normally.

    HINT:
    1. When the transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain location result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



NG
Go to step 7
OK

AFFECTED BY WAVE INTERFERENCE

7. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    w/ Wireless Door Lock Buzzer
    A
    w/o Wireless Door Lock Buzzer
    B



B
Go to step 12
A


8. SWITCH TO SELF DIAGNOSTIC MODE
  1. Switch to self-diagnostic mode by operating the ignition key cylinder.

    1. Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.

    2. Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and then off.

    3. Within 30 seconds of turning the ignition switch off, perform the following 9 operation times: turn the ignition switch to ON and then off.

      NOTICE:
      If the system cannot enter self-diagnostic mode, the system returns to normal mode.

      HINT:
      1. Turning the ignition switch to ON after the above operations have been completed ends self-diagnostic mode.
      2. Do not lock or unlock doors during self-diagnostic mode.

  1. B110075E26
    Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer sound.

    OK:
    Wireless door lock buzzer pattern is same as illustration on left.


NEXT


9. CHECK BY SELF DIAGNOSTIC MODE

  1. Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the wireless door lock buzzer sound.B123864E11

    Result 
    Result
    Proceed to
    Normal waves (wireless door lock buzzer patterns) for LOCK and UNLOCK switches are output
    A
    Unmatching recognition code is output
    B
    No diagnosis outputs
    C



B
Go to step 10

C
Go to step 11
A

REPLACE MAIN BODY ECU

10. REGISTER RECOGNITION CODE
  1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

    OK:
    Recognition code can be registered.



NG
Go to step 15
OK

END

11. CHECK RESPONSE OF DOOR CONTROL RECEIVER
  1. Prepare the door control transmitter from another vehicle.

  1. Press and hold down the door control transmitter switch.

  1. Check that the an unmatching recognition code is out put.

OK:
Unmatching recognition code is output.



NG
Go to step 12
OK

REPLACE DOOR CONTROL TRANSMITTER MODULE (Click here)

12. CHECK DOOR CONTROL RECEIVER (POWER SOURCE AND GROUND)
B194242E03
  1. Disconnect the door control receiver connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1(GND) - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    5(+B) - Body ground
    Always
    11 to 14 V

  1. Reconnect the door control receiver connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. CHECK DOOR CONTROL RECEIVER (OUTPUT)
B177996E06
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E23-2 (RDA) - Body ground
    Transmitter switch OFF → ON (No key in ignition key cylinder, all doors closed)
    6 V or higher → Below 1 V → 6 V or higher



NG
REPLACE DOOR CONTROL RECEIVER
OK


14. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
B195636E01
  1. Disconnect the E7 main body ECU connector and the E23 door control receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-4 (RDA) - E23-2(RDA)
    Always
    Below 1 Ω
    E7-4 (RDA) - Body ground
    Always
    10 kΩ or higher
    E7-3 (PRG) - E23-3 (PRG)
    Always
    Below 1 Ω
    E7-3 (PRG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector and the door control receiver connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15. REPLACE DOOR CONTROL RECEIVER
  1. Temporarily replace the door control receiver with a new or normally functioning one.


NEXT


16. REGISTER RECOGNITION CODE
  1. Perform the Registration procedures (Click here).


NEXT


17. CHECK DOOR CONTROL RECEIVER (OPERATION)
  1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE MAIN BODY ECU
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)


← ON-VEHICLE INSPECTION (from Nov 2010)Only Wireless Control Function is Inoperative (from Nov 2010) →