2011-2016 FJ Cruiser · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Jul 2007


1. INSPECT DIFFERENTIAL RING GEAR BACKLASH

R012683E01
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-32011  

    Standard:
    0.11 to 0.21 mm (0.0043 to 0.0083 in.)

    1. If the backlash is not as specified, adjust the side bearing preload or repair as necessary.

      HINT:
      Perform the measurements at 3 or more positions around the side bearing preload.


2. INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

F001237E05
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum runout:
    Runout
    Maximum
    Vertical runout
    0.10 mm (0.0039 in.)
    Lateral runout
    0.10 mm (0.0039 in.)

    1. If the runout is greater than the maximum, replace the companion flange.


3. INSPECT DRIVE PINION PRELOAD

FA01158E01
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    HINT:
    Bolts without torque specifications are shown in the service data (Click here).


4. INSPECT TOTAL PRELOAD

FA01158E01
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    HINT:
    Bolts without torque specifications are shown in the service data (Click here).

    1. If necessary, disassemble and inspect the differential.


5. REMOVE AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR

G023135E01
  1. Remove the 4 bolts.

  1. Using a hammer, pry out the actuator from the differential tube.


6. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY

C097021E01
  1. Remove the 4 bolts.

  1. Using a plastic-faced hammer, tap out the differential tube.


7. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

F044345E01
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  


8. REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY

G023136E01
  1. Using SST, remove the inter shaft.

    SST
    09350-20015   (09369-20040)
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)

  1. Remove the snap ring from the inter shaft.


9. REMOVE FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR

G023164E01
  1. Using a screwdriver with its tip wrapped in protective tape, pry out the bearing retainer deflector.


10. REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT

F044346E01
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010  

  1. SA02349E03
    Using SST to hold the companion flange in place, remove the nut.
    SST
    09330-00021  


11. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

B087869E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.


12. REMOVE FRONT DIFFERENTIAL DUST DEFLECTOR

F040564E02
  1. Using SST and a press, press out the dust deflector.

    SST
    09950-00020  
    09950-60010   (09951-00510)
    09950-70010   (09951-07150)

    NOTICE:
    Do not drop the companion flange.


13. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

SA02348E02
  1. Using SST, remove the oil seal from the differential carrier.

    SST
    09308-10010  


14. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
  1. Remove the oil slinger from the drive pinion.


15. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

Z000641E01
  1. Using SST, remove the roller bearing (inner) from the drive pinion.

    SST
    09556-22010  

  1. Remove the bearing spacer.


16. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
  1. Remove the 10 bolts and tap out the retainer with a plastic-faced hammer.


17. REMOVE DIFFERENTIAL CASE ASSEMBLY

18. REMOVE DIFFERENTIAL DRIVE PINION

19. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

R002482E01
  1. Using SST and a press, press out the roller bearing (inner) from the drive pinion.

    SST
    09950-00020  

    NOTICE:
    Do not drop the drive pinion.

    HINT:
    If the drive pinion or ring gear is damaged, replace them as a set.


20. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

R013226E01
  1. Using a brass bar and hammer, tap out the roller bearing (outer).


21. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

R013210E01
  1. Using SST, remove the roller bearing (outer).

    SST
    09502-12010  
    09612-65014   (09612-01020, 09612-01050)


22. REMOVE FRONT DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap out the oil storage ring.


23. REMOVE FRONT DIFFERENTIAL CASE BEARING

F044347E01

HINT:
  1. Measure the thickness of the case washer.
  1. Tag the bearing outer races to show the location for reassembly.

  1. Using SST and a press, press out the case bearing (outer race) and plate washer from the bearing retainer.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)
    1. If the bearing is damaged during removal, replace it.

  1. F044348E01
    Using SST and a press, press out the case bearing (outer race) and plate washer from the differential carrier.
    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)
    1. If the bearing is damaged during removal, replace it.


24. REMOVE DIFFERENTIAL RING GEAR

C113176E01
  1. Place matchmarks on the ring gear and differential case.

  1. Remove the 10 ring gear set bolts.

  1. C014054E01
    Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


25. REMOVE FRONT DIFFERENTIAL CASE BEARING

R011392E01

HINT:
The differential case and case bearings should only be removed when replacement is necessary.

  1. Using SST, remove the 2 case bearings (inner) from the differential case.

    SST
    09950-60010   (09951-00480)
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09953-04020, 09958-04011)

    HINT:
    Fix the claws of SST to the notch in the differential case assembly.


26. DISASSEMBLE DIFFERENTIAL CASE

C080046E01
  1. Using a chisel and hammer, unstake the differential case.

  1. G020264E01
    Using a pin punch and hammer, tap out the straight pin.

  1. B084283E01
    F044349E01
    Remove the following parts from the differential case.
    1. (1) Differential pinion gear (2 pieces)
    2. (2) Differential pinion gear thrust washer (2 pieces)
    3. (3) Differential pinion shaft
    4. (4) Differential side gear (2 pieces)
    5. (5) Differential side gear thrust washer (2 pieces)


27. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that the differential pinion and differential side gear are not damaged.

    1. If the differential pinion or differential side gear is damaged, replace the differential gear kit.


28. INSPECT FRONT DIFFERENTIAL CASE
  1. Check that the differential case is not damaged.

    1. If the differential case is damaged, replace it.


29. REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING

SA00353E01
  1. Using a brass bar and hammer, tap out the 2 bearings.


30. REMOVE DIFFERENTIAL CLUTCH HUB

G023137E01
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the differential clutch hub.


31. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

F044350E01
  1. Using SST, tap out the oil seal from the differential tube.

    SST
    09308-00010  


32. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

C097022E01
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the shaft from the differential tube.


33. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING

R013420E01
  1. Using a snap ring expander, remove the snap ring.

  1. Using SST, a brass bar and a press, press out the shaft RH bearing.

    SST
    09950-00020  

    NOTICE:
    1. Do not damage the bearing.
    1. Do not drop the shaft.


34. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB

G023141E01
  1. Check that there is no wear or damage on the clutch hub and clutch sleeve.

    1. Replace parts as necessary.

  1. Check that the clutch sleeve slides smoothly on the clutch hub.
    Replace parts as necessary.


35. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL SIDE GEAR INTER SHAFT

G023144E01
  1. Check that there is no wear or damage on the clutch sleeve and side gear inter shaft.

    1. Replace parts as necessary.

  1. Check that the clutch sleeve slides smoothly on the side gear inter shaft.
    Replace parts as necessary.


36. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE

G023142E01
  1. Using a feeler gauge, measure the clearance between the sleeve fork and clutch sleeve.

    Maximum clearance:
    0.15 to 0.35 mm (0.0059 to 0.0138 in.)

    1. If the clearance is greater than the maximum, replace the fork or clutch sleeve.

← REMOVAL (from Jul 2007)REASSEMBLY (from Jul 2007) →