DISASSEMBLY
Removal / installation · Vehicles built Jul 2007 – Jul 2009
Versions by build date: Jul 2007 – Jul 2009 from Aug 2009
| 1.
FIX REAR DIFFERENTIAL CARRIER ASSEMBLY |
 |
| 2.
INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR |
 |
Using a dial indicator, measure the runout of the companion flange vertically and laterally.
- Maximum runout:
Runout
|
Maximum
|
Vertical runout
|
0.10 mm (0.0039 in.)
|
Lateral runout
|
0.10 mm (0.0039 in.)
|
- If the runout is greater than the maximum, replace the companion flange.
| 3.
INSPECT RUNOUT OF DIFFERENTIAL RING GEAR |
 |
Using a dial indicator, check the runout of the ring gear.
- Maximum runout:
- 0.07 mm (0.0028 in.)
- If the runout is greater than the maximum, replace the ring gear with a new one.
| 4.
INSPECT DIFFERENTIAL RING GEAR BACKLASH |
 |
Using a dial indicator, check the backlash of the ring gear.
- Backlash:
- 0.13 to 0.18 mm (0.0051 to 0.0071 in.)
- If the backlash is not within the specification, adjust the side bearing preload or repair as necessary.
- HINT:
- Perform the measurements at 3 or more positions around the side bearing preload.
| 5.
INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
 |
Using a torque wrench, measure the preload of backlash between the drive pinion and ring gear.
- Preload (at starting):
- 0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 5.0 to 7.5 in.*lbf)
If necessary, disassemble and inspect the differential.
| 6.
INSPECT TOTAL PRELOAD |
 |
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
Using a torque wrench, measure the total preload.
- Total preload (at starting):
- Drive pinion preload plus 0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)
If necessary, disassemble and inspect the differential.
| 7.
REMOVE REAR DRIVE PINION NUT |
 |
Using SST and a hammer, loosen the staked part of the nut.
- SST
- 09930-00010
- Using SST to hold the companion flange in place, remove the nut.
- SST
- 09330-00021
| 8.
REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
 |
Using SST, remove the companion flange.
- SST
- 09950-30012
(09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)
- NOTICE:
- Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
| 9.
REMOVE REAR DIFFERENTIAL DUST DEFLECTOR |
 |
Using SST and a press, press out the dust deflector.
- SST
- 09950-60010
(09951-00380)
09950-70010
(09951-07150)
09950-00020
- NOTICE:
- Do not drop the companion flange.
| 10.
REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL |
 |
Using SST, remove the oil seal from the differential carrier.
- SST
- 09308-10010
| 11.
REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
|
| 12.
REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
 |
Using SST, remove the roller bearing (inner) from the drive pinion.
- SST
- 09556-22010
| 13.
REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK |
 |
Remove the 2 bolts and 2 adjusting locks.
| 14.
REMOVE DIFFERENTIAL CASE ASSEMBLY |
 |
Place matchmarks on the bearing cap and differential carrier.
Remove the 4 bolts and 2 differential bearing caps.
Remove the 2 adjusting nuts.
- Remove the rear differential case assembly from the differential carrier.
- HINT:
- Tag the 2 case bearing outer races to show the location for reassembly.
| 15.
REMOVE DIFFERENTIAL DRIVE PINION |
 |
- Remove the drive pinion and bearing spacer from the differential carrier.
| 16.
REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
 |
Using SST and a press, press out the roller bearing (inner) from the drive pinion.
- SST
- 09950-00020
- NOTICE:
- Do not drop the drive pinion.
- HINT:
- If the drive pinion or ring gear is damaged, replace them as a set.
| 17.
REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER |
|
| 18.
REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
 |
Using SST, remove the roller bearing (outer) from the carrier.
- SST
- 09308-00010
Using a brass bar and hammer, tap out the oil storage ring from the carrier.
- HINT:
- If the bearing is damaged during removal, replace it.
| 19.
REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
 |
Using a brass bar and hammer, tap out the rear tapered roller bearing (outer) from the carrier.
- HINT:
- If the bearing is damaged during removal, replace it.
| 20.
REMOVE DIFFERENTIAL RING GEAR |
 |
Place matchmarks on the ring gear and differential case.
Using a screwdriver and hammer, pry out the lock plates.
Remove the 10 ring gear set bolts and 5 lock plates.
- Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.
| 21.
INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT |
 |
Install the rear differential case bearing onto the differential case.
Install the differential case onto the differential carrier.
Install the 2 bearing caps onto the differential carrier with the 4 bolts.
-
Torque:
- 85 N*m{
870 kgf*cm
, 63 ft.*lbf
}
Using a dial indicator, measure the differential case runout.
- Maximum runout:
- 0.07 mm (0.0028 in.)
Remove the differential case.
Remove the rear differential case bearing.
| 22.
REMOVE REAR DIFFERENTIAL CASE BEARING |
 |
Using SST, remove the 2 bearings from the differential case.
- SST
- 09950-40011
(09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010
(09951-00360)
- HINT:
- Do not remove the case bearing unless replacing the differential case.
| 23.
DISASSEMBLE DIFFERENTIAL CASE |
 |
Place matchmarks on the LH and RH cases.
Remove the 8 bolts.
- Using a plastic hammer, separate the LH and RH cases.
- Remove the following parts from the differential case.
A
|
Side gear
|
B
|
Side gear thrust washer
|
C
|
Spider
|
D
|
Pinion gear
|
E
|
Pinion gear thrust washer
|