2011-2016 FJ Cruiser · Service Manual DRIVE LINE

REASSEMBLY

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. ASSEMBLE DIFFERENTIAL CASE

  1. ZK01881
    Install the rear differential side gear thrust washer onto the rear differential side gear.

  1. Install the rear differential pinion thrust washer and rear differential pinion onto the rear differential spider.

  1. Fix the differential case RH.

  1. ZK09096
    Install the rear differential side gear and rear differential spider onto the differential case RH.

  1. ZK09097
    Using a dial indicator, measure the differential case RH side backlash while holding the pinion toward the case.

    Backlash:
    0.05 to 0.20 mm (0.002 to 0.008 in.)

  1. Remove the rear differential spider from the differential case RH.

  1. ZK09098
    Install the rear differential side gear and rear differential spider onto the differential case LH.

  1. Using a dial indicator, measure the differential case LH side backlash while holding the pinion toward the case.

    Backlash:
    0.05 to 0.20 mm (0.002 to 0.008 in.)

    If the backlash is not within the specification, install 2 side gear thrust washers of a different thickness.

    Thrust washer thickness:
    Thickness mm (in.)
    Thickness mm (in.)
    0.9 (0.0354)
    1.2 (0.0472)
    1.0 (0.0394)
    1.3 (0.0512)
    1.1 (0.0433)
    -

  1. C089323E02
    Align the matchmarks and assemble the RH and LH cases.

  1. Using a plastic hammer, install the differential case.

  1. Install the 8 bolts.

    Torque:
    47 N*m{ 480 kgf*cm , 35 ft.*lbf }


2. INSTALL DIFFERENTIAL RING GEAR

SA01143E01
  1. Clean the contact surfaces of the differential case and ring gear.

  1. Heat the ring gear in water that is approximately 100°C (212°F).

  1. Carefully remove the ring gear from the boiling water.

  1. After the moisture on the ring gear has completely evaporated, quickly install the ring gear onto the differential case.

  1. C093504
    Align the matchmarks on the ring gear with those of the differential case.

  1. Temporarily install 5 new lock plates and the 10 bolts.

  1. After the ring gear cools down, install the 10 bolts by diametrically tightening the bolts uniformly in several steps.

    Torque:
    97 N*m{ 989 kgf*cm , 72 ft.*lbf }

  1. Z002483E01
    Using a chisel and hammer, stake the 5 lock plates.

    HINT:
    Strike the tab labeled A so that it is flush with the flat surface of the bolt. Strike the tab labeled B so that half of the tab is in contact with the bolt as shown in the illustration.


3. INSTALL REAR DIFFERENTIAL CASE BEARING

C090326E05
  1. Using SST and a press, press the bearing onto the differential case.

    SST
    09950-60010   (09951-00430, 09951-00480, 09951-00470, 09951-00550)
    09950-70010   (09951-07150, 09951-00560, 09951-00570)


4. INSPECT DIFFERENTIAL RING GEAR RUNOUT

C014075E01
  1. Install the differential case on the carrier, and install the 2 adjusting nuts so that there is no play in the bearing.

  1. Install the 2 bearing caps with the 4 bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

  1. Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the 2 bearing caps, 2 adjusting nuts and the differential case.


5. INSTALL REAR DIFFERENTIAL DUST DEFLECTOR

C113183E02
  1. Using SST, a plate and a press, press in a new dust deflector.

    SST
    09636-20010  

    NOTICE:
    Be careful not to damage the dust deflector.


6. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

C197664E01
  1. Using SST and a press, press in the roller bearing (outer) to the carrier.

    SST
    09316-60011   (09316-00011, 09316-00021)


7. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

C197665E01
  1. Using SST and a press, press the roller bearing (outer) into the carrier.

    SST
    09316-60011   (09316-00041, 09316-00011)


8. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

SA03102E02
  1. Install the plate washer onto the drive pinion.

    HINT:
    First fit a washer with the same thickness as the removed washer, and then check the tooth contact pattern. Replace the washer with one of a different thickness if necessary.

  1. Using SST and a press, press the roller bearing (inner) onto the drive pinion.

    SST
    09506-30012  


9. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

C028218E01
  1. Install the drive pinion, rear drive pinion tapered roller bearing and rear differential drive pinion oil slinger.

    HINT:
    Assemble the spacer and oil seal after adjusting the gear contact pattern.

  1. R011163E03
    Using SST, install the companion flange.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. C014066E01
    Adjust the drive pinion preload by tightening the companion flange nut.

  1. Using SST to hold the companion flange in place, torque the nut.

    SST
    09330-00021  

    Torque:
    370 N*m{ 3,770 kgf*cm , 273 ft.*lbf } or less

    NOTICE:
    1. As there is no spacer, torque a little at a time. Be careful not to overtighten the nut.
    1. Apply hypoid gear oil to the nut.

  1. C003092
    Using a torque wrench, measure the preload.

    Preload (at starting):
    Bearing
    Standard
    New bearing
    1.05 to 1.64 N*m (10.7 to 16.7 kgf*cm, 9.3 to 14.5 in.*lbf)
    Used bearing
    0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 4.9 to 7.5 in.*lbf)

    NOTICE:
    For a more accurate measurement, rotate the bearing forward and backward several times before measuring.


10. INSTALL DIFFERENTIAL CASE ASSEMBLY

C028220E01
  1. Place the 2 bearing outer races on their respective bearings.

    HINT:
    Do not interchange the right and left races.


11. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT

C028221E01
  1. Install the 2 adjusting nuts onto the carrier, making sure the nuts are threaded properly.


12. INSPECT AND ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

C030539E01
  1. Align the matchmarks on the cap and carrier.

  1. SA02474E01
    Install the right and left bearing caps with the 4 bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

    1. If the bearing cap does not fit tightly on the carrier, the adjusting nuts are not threaded properly.

      HINT:
      Reinstall the adjusting nuts if necessary.

  1. Z000693E01
    Loosen the 4 bearing cap bolts to the point where the adjusting nuts can be turned using SST.

  1. Using SST, torque the adjusting nut on the ring gear side until the ring has a backlash of about 0.2 mm (0.008 in.).

    SST
    09504-00011  

  1. Z006917E01
    While turning the ring gear, use SST to fully tighten the adjusting nut on the drive pinion side. After the bearings have settled, loosen the adjusting nut on the drive pinion side.

  1. Using SST, tighten the adjusting nut 1 to 1.5 notches from the 0 preload position.

    SST
    09504-00011  

  1. C013842E01
    Using a dial indicator, adjust the ring gear backlash until it is within the specification.

    Standard backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    HINT:
    1. The backlash is adjusted by turning the left and right adjusting nuts an equal amount. For example, loosen the nut on the right side one notch and loosen the nut on the left side one notch.

    1. Perform the measurement at 3 or more positions around the circumference of the ring gear.

  1. C013841E01
    Torque the bearing cap bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }


13. INSPECT TOTAL PRELOAD

C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Total preload (at starting):
    Drive pinion preload plus 0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)

    If necessary, disassemble and inspect the differential.


14. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

C014071E01
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with prussian blue.

  1. Hold the companion flange firmly in place and rotate the ring gear in both directions.

  1. Inspect the tooth contact pattern.

    1. C113184E01

    2. ZK01912E03
      If the teeth are not engaged properly, use the following chart to select a proper washer.

      Plate Washer Thickness:
      Thickness mm (in.)
      Thickness mm (in.)
      1.69 to 1.71 (0.0665 to 0.0673)
      2.02 to 2.04 (0.0795 to 0.0803)
      1.72 to 1.74 (0.0677 to 0.0685)
      2.05 to 2.07 (0.0807 to 0.0815)
      1.75 to 1.77 (0.0689 to 0.0697)
      2.08 to 2.10 (0.0819 to 0.0827)
      1.78 to 1.80 (0.0701 to 0.0709)
      2.11 to 2.13 (0.0831 to 0.0839)
      1.81 to 1.83 (0.0713 to 0.0720)
      2.14 to 2.16(0.0843 to 0.0850)
      1.84 to 1.86 (0.0724 to 0.0732)
      2.17 to 2.19 (0.0854 to 0.0862)
      1.87 to 1.89 (0.0736 to 0.0744)
      2.20to 2.22 (0.0866 to 0.0874)
      1.90 to 1.92 (0.0748 to 0.0756)
      2.23 to 2.25 (0.0878 to 0.0886)
      1.93 to 1.95 (0.0760 to 0.0768)
      2.26 to 2.28 (0.0890 to 0.0898)
      1.96 to 1.98 (0.0772 to 0.0780)
      2.29 to 2.31 (0.0902 to 0.0909)
      1.99 to 2.01 (0.0783 to 0.0791)
      2.32 to 2.34 (0.0913 to 0.0921)


15. REMOVE REAR DRIVE PINION NUT

SA02349E03
  1. Using SST to hold the companion flange in place, remove the nut.

    SST
    09330-00021  


16. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

B087869E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.


17. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

18. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

F044343E01
  1. Using SST, remove the roller bearing (inner).

    SST
    09556-22010  

  1. W001770E02
    Using SST, tap out the roller bearing (outer).
    SST
    09308-00010  


19. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

C093601E01
  1. Install a new bearing spacer onto the drive pinion.


20. INSTALL DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap in a new oil storage ring.

    NOTICE:
    Be careful not to damage the oil storage ring.


21. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

G021735E01
  1. Using SST and hammer, tap in the roller bearing (outer).

    SST
    09316-60011   (09316-00011, 09316-00021)

  1. Install the roller bearing (inner).


22. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

23. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

Z000698E01
  1. Apply MP grease to a new oil seal.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09554-30011  

    Oil seal depth:
    0.55 to 1.45 mm(0.021 to 0.057)


24. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

R011163E02
  1. Using SST, install the companion flange onto the drive pinion.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. SA02351E03
    Coat the threads of a new nut with hypoid gear oil.

  1. Using SST to hold the flange, torque the nut.

    SST
    09330-00021  

    Torque:
    370 N*m{ 3,770 kgf*cm , 273 ft.*lbf } or less


25. INSPECT DRIVE PINION PRELOAD

SA02352E01
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    Bearing
    Standard
    New bearing
    1.05 to 1.64 N*m (11 to 17 kgf*cm, 9.3 to 15 in.*lbf)
    Used bearing
    0.56 to 0.85 N*m (6 to 9 kgf*cm, 4.9 to 7.5 in.*lbf)

    1. If the preload is greater than the maximum, replace the bearing spacer.
    1. If the preload is less than the minimum, retighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.

    Torque:
    370 N*m{ 3,770 kgf*cm , 273 ft.*lbf } or less

    1. If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload adjusting procedure.

    HINT:
    Do not loosen the pinion nut to reduce the preload.


26. INSPECT TOTAL PRELOAD

SA02352E01
  1. Using a torque wrench, measure the preload.

    HINT:
    Bolt without torque specifications are shown in the service data (Click here).

    1. If necessary, disassemble and inspect the differential.


27. INSPECT DIFFERENTIAL RING GEAR BACKLASH

C028211E01
  1. Using a dial indicator, check the backlash of the ring gear.

    Standard backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    1. If the backlash is not as specified, adjust the side bearing preload or repair as necessary.

      HINT:
      Perform the measurements at 3 or more positions around the circumference of the ring gear.


28. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

F001237E05
  1. Using a dial indicator, measure the runout of the drive pinion companion flange vertically and laterally.

    Maximum runout:
    Runout
    Maximum
    Vertical runout
    0.10 mm (0.0039 in.)
    Lateral runout
    0.10 mm (0.0039 in.)

    1. If the runout is greater than the maximum, replace the companion flange.


29. STAKE DRIVE PINION NUT

ZK07449E01
  1. Using a chisel and hammer, stake the nut.


30. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

C028226E01
  1. Install 2 new adjusting locks onto the bearing caps with the 2 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Bend the nut locks.

    HINT:
    Perform the measurements at 3 or more positions around the circumference of the ring gear.

← INSPECTION (from Aug 2009)REASSEMBLY (from Aug 2009) →