TERMINALS OF ECU
System information · Vehicles built from Aug 2008
| TELEVISION CAMERA ASSEMBLY |
Disconnect the c1 television camera assembly connector.


Measure the voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
c1-3 (CGND) - Body ground
BR - Body ground
Ground
Always
Below 1 V
c1-4 (CB+) - c1-3 (CGND)
B - BR
Power source
Ignition switch ON,
shift lever in R
5.5 to 7.05 V
Reconnect the c1 television camera assembly connector.
Measure the waveform according to the value(s) in the table below.
If the result is not as specified, the camera may have a malfunction.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
c1-1 (CV-) - c1-2 (CV+)
W - R
Display signal
Ignition switch ON,
shift lever in R
Pulse generation
(See waveform)
Using an oscilloscope, check the waveform.

Waveform (Reference) Terminal Connection
c1-1 (CV-) - c1-2 (CV+)
Tester Range
0.2 V/DIV., 50 μs/DIV.
Vehicle Condition
Ignition switch ON,
shift lever in R
| INNER REAR VIEW MIRROR ASSEMBLY |
Disconnect the R6 inner rear view mirror assembly connector.


Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
R6-1 (B/C+) - R6-2 (B/C-)
Y-R - W-B
Ignition switch signal
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
R6-2 (B/C-) - Body ground
W-B - Body ground
Ground
Always
Below 1 V
R6-3 (REV) - R6-2 (B/C-)
R-Y - W-B
Reverse signal
Ignition switch ON,
shift lever not in R
Below 1 V
Ignition switch ON,
shift lever in R
11 to 14 V
R6-6 (CV-) - R6-2 (B/C-)
W - W-B
Signal ground
Always
Below 1 V
R6-10 (BCTY) - Body ground
W - Body ground
Back door courtesy switch signal
Back door is open
Below 1 Ω
Back door is closed
10 kΩ or higher
R6-13 (CGND) - Body ground
Shielded - Body ground
Television camera ground (Shielded)
Always
Below 1 V
R6-14 (CB+) - R6-2 (B/C-)
B - W-B
Power source to television camera
Ignition switch ON,
shift lever in R
5.5 to 7.05 V
Reconnect the R6 inner rear view mirror assembly connector.
Measure the waveform according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
R6-7 (CV+) - R6-6 (CV-)
R - W
Television camera display signal (Input)
Ignition switch ON,
shift lever in R
Pulse generation
(See waveform)
Using an oscilloscope, check the waveform.

Waveform (Reference) Terminal Connection
R6-7 (CV+) - R6-6 (CV-)
Tester Range
0.2 V/DIV., 50 μs/DIV.
Vehicle Condition
Ignition switch ON,
shift lever in R