2011-2016 FJ Cruiser · Service Manual ENGINE

P0112 Intake Air Temperature Circuit Low Input

Diagnostic trouble codes · Vehicles built from Aug 2009

Also covers:

DESCRIPTION


  1. A056276E14
  2. The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
    The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
    Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, according to changes in the IAT, the voltage at terminal THA also varies.
    Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve drivability.

HINT:
When any of DTCs P0112 and P0113 are set, the ECM enters fail-safe mode. During fail-safe mode, the IAT is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.

DTC No.
DTC Detection Condition
Trouble Area
P0112
Short in Intake Air Temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Short in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM
P0113
Open in Intake Air Temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM

HINT:
When any of these DTCs are set, check the IAT by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit


WIRING DIAGRAM

A193263E03

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.

  1. Read the value displayed on the tester.

    OK:
    Same as actual Intake Air Temperature (IAT).

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    Same as actual IAT
    C

    HINT:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or higher.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
A116161E08
  1. Disconnect the Mass Air Flow (MAF) meter connector.

  1. Connect terminals THA and ETHA of the MAF meter wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    140°C (284°F) or higher

    Text in Illustration 
    *1
    MAF Meter
    *2
    ECM
    *3
    Front view of wire harness connector
    (to Mass Air Flow Meter)



NG
Go to step 3
OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER (Click here)

3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)
A226852E01
  1. Disconnect the MAF meter connector.

  1. Connect terminals THA and ETHA of the ECM connector.

    HINT:
    Before checking, do visual and contact pressure checks on the ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    140°C (284°F) or higher.

    Text in Illustration 
    *1
    MAF Meter
    *2
    ECM
    *3
    Rear view of wire harness connector
    (to ECM)



NG
CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
A193223E03
  1. Disconnect the MAF meter connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    -40°C (-40°F)

    Text in Illustration 
    *1
    MAF Meter
    *2
    ECM



NG
Go to step 5
OK

REPLACE MASS AIR FLOW METER (Click here)

5. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT ECM)
A226850E01
  1. Disconnect the ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    -40°C (-40°F)

    Text in Illustration 
    *1
    MAF Meter
    *2
    ECM
    *3
    Rear view of wire harness connector
    (to ECM)



NG
REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)


← P0110 Intake Air Temperature Circuit (+ P0112, P0113) (Jul 2007 – Jul 2009)P0115 Engine Coolant Temperature Circuit (+ P0117, P0118) (Jul 2007 – Jul 2009) →