P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit
Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009
Also covers:
- P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input
- P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input
- P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit
- P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input
- P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input
- P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation
DESCRIPTION
- HINT:
- These DTCs relate to the Throttle Position (TP) sensor.
The TP sensor has two sensor circuits which each transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.


| DTC No. |
DTC Detection Conditions |
Trouble Areas |
| P0120 |
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0122 |
Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0123 |
Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0220 |
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0222 |
Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0223 |
Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V, for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P2135 |
Either condition (a) or (b) met (1 trip detection logic)
|
|
- HINT:
- When any of these DTCs are set, check the throttle valve opening angle by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
- Throttle Position No. 1 denotes the VTA1 signal, and Throttle Position No. 2 denotes the VTA2 signal .
- Reference (Normal Condition):
Tester Display
Accelerator Pedal Fully Released
Accelerator Pedal Fully Depressed
Throttle Position No. 1
0.5 to 1.1 V
3.3 to 4.9 V
Throttle Position No. 2
2.1 to 3.1 V
4.6 to 5.0 V
- When any of these DTCs are set, check the throttle valve opening angle by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
MONITOR DESCRIPTION
The ECM uses the Throttle Position (TP) sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the TP sensor.- A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor, and sets a DTC.
- VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor, and sets a DTC.
- VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor, and sets a DTC.
FAIL-SAFE
When any of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed.If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned OFF.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
- Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
- If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
| 1. READ VALUE USING INTELLIGENT TESTER (THROTTLE POS #1 AND THROTTLE POS #2) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
Check the values displayed on the tester.
- Result:
When Accelerator Pedal Released
When Accelerator Pedal Depressed
Trouble Areas
Proceed To
Throttle Position No.1
(VTA1)
Throttle Position No.2
(VTA2)
Throttle Position No.1
(VTA1)
Throttle Position No.2
(VTA2)
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
VC circuit open
A
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
E2 circuit open
A
0 to 0.2 V, or 4.5 to 5.0 V
Approximately 2.55 V
(Fail-safe)
0 to 0.2 V, or 4.5 to 5.0 V
Approximately 2.55 V
(Fail-safe)
VTA1 circuit open
or ground short
A
Approximately 0.93 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
Approximately 0.93 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
VTA2 circuit open
or ground short
A
0.5 to 1.1 V
2.1 to 3.1 V
3.3 to 4.9 V
4.6 to 5.0 V
TP sensor circuit
normal
B
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
Disconnect the B14 throttle with motor body connector.

Disconnect the B1 ECM connector.
Check the resistance.
- Standard Resistance (Check for open):
Tester Connections
Specified Conditions
VC (B14-5) - VC (B1-23)
Below 1 Ω
VTA (B14-6) - VTA1 (B1-20)
VTA2 (B14-4) - VTA2 (B1-19)
E2 (B14-3) - E2 (B1-28)
- Standard Resistance (Check for short):
Tester Connections
Specified Conditions
VC (B14-5) or VC (B1-23) - Body grouB14nd
10 kΩ or higher
VTA (B14-6) or VTA1 (B1-20) - Body ground
VTA2 (B14-4) or VTA2 (B1-19) - Body ground
Reconnect the throttle with motor body connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. INSPECT ECM (VC VOLTAGE) |
Disconnect the B14 throttle with motor body connector.

Turn the ignition switch ON.
Measure the voltage between the terminals of the B1 ECM connector.
- Standard Voltage:
Tester Connections
Specified Conditions
VC (B1-23) - E2 (B1-28)
4.5 to 5.5 V
Reconnect the throttle with motor body connector.
|
|
||||
| OK | |
| 4. REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
| NEXT | |
| 5. CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed To
P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135
A
No output
B
|
|
||||
| A | ||
| ||
