2011-2016 FJ Cruiser · Service Manual STEERING

REMOVAL

Removal / installation · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014


1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


3. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


4. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


5. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip LH.


6. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B133853
    Disengage the 4 clips and 2 claws and remove the instrument panel register.

    NOTICE:
    1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
    2. Pull the instrument panel register up diagonally to remove it.


7. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

  1. B133859
    Disengage the 3 claws and separate the hood lock control lever.


8. SEPARATE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for RHD)

  1. B267057
    Disengage the 3 claws and separate the fuel lid lock open lever.


9. REMOVE INSTRUMENT PANEL FINISH PLATE

  1. E149562E03
    Using a screwdriver with its tip wrapped in protective tape, remove the instrument panel finish plate.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Instrument Panel Finish Plate


10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)

  1. B133860
    Remove the 2 <E> bolts.

  1. Disengage the 5 clips and claw and remove the lower instrument panel finish panel.


11. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)

  1. B267058
    Remove the 2 <E> bolts.

  1. Disengage the 8 clips and 4 guides.

  1. Disconnect the connectors and remove the lower instrument panel finish panel.


12. REMOVE LOWER INSTRUMENT PANEL LH (for LHD)

  1. B133864
    Remove the 4 <E> bolts and the lower instrument panel.


13. REMOVE FRONT FLOOR FOOTREST (for LHD)

  1. B130586
    Disengage the 4 claws and remove the front floor footrest.


14. REMOVE NO. 1 AIR DUCT (for LHD)

  1. I102434
    Disengage the 3 claws and remove the air duct.


15. REMOVE NO. 1 AIR DUCT (for RHD)

  1. I105841
    Remove the screw.

  1. Disengage the 2 claws and remove the air duct.


16. REMOVE STEERING COLUMN HOLE COVER

F051329E01
  1. Disengage the 4 clips and remove the steering column hole cover.


17. REMOVE LOWER NO. 3 STEERING WHEEL COVER

  1. C128195
    Using a thin-bladed screwdriver, remove steering wheel cover lower No.3.

    HINT:
    Tape up the screwdriver tip before use.


18. REMOVE LOWER NO. 2 STEERING WHEEL COVER

  1. C128196
    Using a thin-bladed screwdriver, remove steering wheel cover lower No.2.

    HINT:
    Tape up the screwdriver tip before use.


19. REMOVE STEERING PAD

  1. C128197E01
    Using "Torx" socket wrench (T30), loosen the 2 "Torx" screws until the groove along the screw circumference catches on the screw case.

  1. C128193E01
    Pull the steering pad out of the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector.

  1. Disconnect the 2 connectors from the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the steering pad.


20. REMOVE STEERING WHEEL ASSEMBLY

C133806E03
Text in Illustration 
*a
Matchmark
*b
Hold
*c
Turn
  1. Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the main shaft assembly.

  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (center bolt) before use.


21. REMOVE LOWER STEERING COLUMN COVER

C234531
  1. Remove the 3 screws.

  1. Disengage the 2 claws and remove the lower steering column cover.


22. REMOVE UPPER STEERING COLUMN COVER

C231841
  1. Disengage the claw and remove the upper steering column cover.


23. REMOVE COMBINATION SWITCH ASSEMBLY

C231843
  1. Disconnect all connectors from the combination switch assembly.

  1. Remove the 3 screws and the combination switch assembly.


24. REMOVE FRONT WHEEL LH

25. REMOVE FRONT FENDER SPLASH SHIELD REAR LH

A223335
  1. Remove the 5 clips and frame seal.


26. REMOVE STEERING SLIDING YOKE

C233041E01
  1. Put matchmarks on the steering sliding yoke, No. 2 steering intermediate shaft sub-assembly and steering intermediate shaft assembly.

    Text in Illustration 
    *a
    Matchmark

  1. Remove the 2 bolts from the steering sliding yoke.

  1. Slide the steering sliding yoke up and separate it from the No. 2 steering intermediate shaft sub-assembly.

  1. Pull down the steering sliding yoke from the steering intermediate shaft assembly to remove.


27. REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

C233042
  1. Remove the 4 bolts and the No. 1 steering column hole cover sub-assembly.


28. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

C233043E01
  1. Put matchmarks on the No. 2 steering intermediate shaft sub-assembly and the power steering link.

    Text in Illustration 
    *a
    Matchmark

  1. Remove the bolt and the No. 2 steering intermediate shaft sub-assembly from the power steering link.


29. REMOVE STEERING COLUMN ASSEMBLY

C233044
  1. Disconnect all connectors and disengage the 2 wire harness clamps from the steering column assembly.

  1. Remove the 4 nuts and the steering column assembly from the instrument panel reinforcement assembly.

← REMOVAL (Jul 2007 – Oct 2010)REMOVAL (Aug 2012 – Jul 2014) →