Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.
2.
REMOVE FRONT DOOR SCUFF PLATE RH
Disengage the 6 claws and remove the access door scuff plate.
3.
REMOVE FRONT DOOR SCUFF PLATE LH
HINT:
Use the same procedure as for the RH side.
4.
REMOVE FRONT FLOOR FOOTREST
Disengage the 4 claws and remove the front floor footrest.
5.
REMOVE FOOTREST CLIP
Remove the 2 footrest clips.
6.
REMOVE COWL SIDE TRIM BOARD RH
Remove the clip.
Disengage the 2 claws and remove the cowl side trim board.
7.
REMOVE COWL SIDE TRIM BOARD LH
HINT:
Use the same procedure as for the RH side.
8.
SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Remove the front door opening trim weatherstrip to the extent that the front pillar garnish and the instrument panel lower finish panel can be removed.
9.
SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Use the same procedure as for the RH side.
10.
REMOVE ASSIST GRIP PLUG
HINT:
Use the same procedure to remove all the assist grip plugs.
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.
11.
REMOVE ASSIST GRIP ASSEMBLY
HINT:
Use the same procedure to remove all the assist grips.
Remove the 2 screws and the assist grip.
12.
REMOVE FRONT PILLAR GARNISH RH
w/ Assist Grip:
Disengage the 2 clips and the guide and remove the front pillar garnish.
w/o Assist Grip:
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
Text in Illustration
*1
Protective Tape
Remove the bolt.
Disengage the 2 clips and the guide and remove the front pillar garnish.
13.
REMOVE FRONT PILLAR GARNISH LH
HINT:
Use the same procedure as for the RH side.
14.
REMOVE ASSIST GRIP RETAINER RH
Remove the 2 bolts and remove the assist grip retainer.
15.
REMOVE ASSIST GRIP RETAINER LH
HINT:
Use the same procedure as for the RH side.
16.
REMOVE INSTRUMENT PANEL GARNISH LH
Remove screw <G>.
Disengage the 3 clips and remove the instrument panel garnish.
NOTICE:
Pull the instrument panel garnish up at an angle of 45° to remove it.
Do not damage the surface of the instrument panel when removing it.
17.
REMOVE INSTRUMENT PANEL GARNISH RH
Remove screw <G>.
Disengage the 3 clips and remove the instrument panel garnish.
NOTICE:
Pull the instrument panel garnish up at an angle of 45° to remove it.
Do not damage the surface of the instrument panel when removing it.
18.
REMOVE INTEGRATION CONTROL PANEL ASSEMBLY
Remove the 2 screws.
Disengage the 4 clips and remove the integration control panel assembly.
Disconnect the 3 connectors.
19.
REMOVE RADIO RECEIVER ASSEMBLY
Remove the 4 bolts.
Disconnect the connectors and remove the radio receiver.
20.
REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY
Disengage the 4 claws.
Slide the parking brake hole cover toward the front of the vehicle, disengage the 2 guides and remove the parking brake hole cover.
21.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)
Remove the shift lever knob.
22.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD)
Remove the shift lever knob.
23.
REMOVE FRONT CONSOLE BOX UPPER PANEL SUB-ASSEMBLY
Shift the shift lever into the N position.
Disengage the 5 clips and 3 guides and remove the console upper rear panel.
24.
REMOVE FRONT CONSOLE BOX BOTTOM MAT
Remove the box bottom mat.
25.
REMOVE FRONT CONSOLE BOX
Remove the 4 <H> bolts.
Disengage the 5 guides and remove the console box.
26.
REMOVE FRONT CONSOLE BOX UPPER PANEL GARNISH
Disengage claw and the clip.
Slide the console upper panel garnish toward the rear of the vehicle, disengage the guide and remove the console upper panel garnish.
27.
REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY
Remove the 2 clips and 2 <E> bolts.
Disengage the 3 clips and 2 claws and remove the instrument lower cover.
28.
REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY LH
Disengage the 4 clips and 2 claws and remove the instrument panel register.
NOTICE:
To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
Pull the instrument panel register up diagonally to remove it.
29.
REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Disengage the 3 claws and separate the hood lock control lever.
Disengage the 5 clips and claw and remove the lower instrument panel finish panel.
31.
REMOVE INSTRUMENT LOWER PANEL
Remove the 4 <E> bolts and the lower instrument panel.
32.
REMOVE INSTRUMENT CLUSTER LOWER FINISH PANEL
Disengage the 3 clips and the 4 claws and remove the instrument cluster finish panel.
Disconnect the connectors.
33.
REMOVE COMBINATION METER ASSEMBLY
Remove the 4 screws.
Disconnect the 2 connectors and clamp and remove the combination meter.
34.
REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
Disengage the claw and separate the glove compartment door stoppers from the glove compartment door.
Text in Illustration
*1
Stopper
Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.
Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.