2011-2016 FJ Cruiser · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Aug 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

NOTICE:
  1. Before starting the work, make sure that the ignition switch off and depress the brake pedal more than 20 times.
  2. As high pressure is applied to the brake actuator No. 1 tube, never deform it.
  3. Do not turn the ignition switch to ON until the work is completed.

HINT:
When the pressure in the accumulator is released, the reaction force becomes lighter and the stroke becomes longer.


1. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with a painted surface.


2. REMOVE FRONT DOOR SCUFF PLATE

HINT:
Use the same procedure as for the RH side.


3. REMOVE FRONT FLOOR FOOTREST

  1. B130586
    Disengage the 4 claws and remove the front floor footrest.


4. REMOVE FOOTREST CLIP

  1. B130587
    Remove the 2 footrest clips.


5. REMOVE COWL SIDE TRIM BOARD

HINT:
Use the same procedure as for the RH side.


6. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP
  1. Separate the front door opening trim weatherstrip LH.


7. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B133853
    Disengage the 4 clips and 2 claws and remove the instrument panel register.

    NOTICE:
    1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
    2. Pull the instrument panel register up diagonally to remove it.


8. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

  1. B133859
    Disengage the 3 claws and separate the hood lock control lever.


9. SEPARATE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for RHD)

  1. B267057
    Disengage the 3 claws and separate the fuel lid lock open lever.


10. REMOVE INSTRUMENT PANEL FINISH PLATE

  1. E149562E03
    Using a screwdriver with its tip wrapped in protective tape, remove the instrument panel finish plate.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Instrument Panel Finish Plate


11. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)

  1. B133860
    Remove the 2 <E> bolts.

  1. Disengage the 5 clips and claw and remove the lower instrument panel finish panel.


12. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)

  1. B267058
    Remove the 2 <E> bolts.

  1. Disengage the 8 clips and 4 guides.

  1. Disconnect the connectors and remove the lower instrument panel finish panel.


13. SEPARATE MASTER CYLINDER PUSH ROD CLEVIS

F050561
  1. Remove the clip and push rod pin and separate the push rod clevis.


14. REMOVE HYDRAULIC BRAKE BOOSTER (for LHD)

F051438E01
  1. Disconnect the 3 connectors from the hydraulic brake booster.

  1. C232823
    Using a union nut wrench 10 mm, disconnect the 4 brake tubes from the hydraulic brake booster.

  1. C133114E02
    Use tags or labels to identify the place to reconnect each line.
    Text in Illustration 
    *a
    To front wheel cylinder RH
    *b
    To front wheel cylinder LH
    *c
    To rear wheel cylinder RH
    *d
    To rear wheel cylinder LH

  1. F050571
    Remove the 4 nuts and pull out the hydraulic brake booster.

  1. Remove the gasket from the hydraulic brake booster.


15. REMOVE HYDRAULIC BRAKE BOOSTER (for RHD)

C213446
  1. Disconnect the 3 connectors from the hydraulic brake booster.

  1. F051200E07
    Use tags or labels to identify the place to reconnect each line.
    Text in Illustration 
    *a
    To front wheel cylinder RH
    *b
    To front wheel cylinder LH
    *c
    To rear wheel cylinder RH
    *d
    To rear wheel cylinder LH

  1. C213447
    Using a union nut wrench 10 mm, disconnect the 4 brake tubes from the hydraulic brake booster.

  1. Remove the bolt and the brake tube clamp from the hydraulic brake booster assembly.

  1. Remove the brake tube clamp from the brake tube.

  1. C231004
    Remove the 4 nuts and pull out the hydraulic brake booster.

  1. Remove the gasket from the hydraulic brake booster.

← REMOVAL (Nov 2010 – Jul 2012)DISASSEMBLY (from Jul 2007) →