2011-2016 FJ Cruiser · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY

B133898E02
  1. Disengage the 2 A claws and 2 B claws.

  1. Slide the parking brake hole cover toward the front of the vehicle, disengage the 2 C claws and remove the parking brake hole cover.


3. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY

  1. B133897
    Shift the shift lever into the N position.

  1. Disengage the 5 clips and 3 claws and remove the console upper rear panel.


4. REMOVE FRONT CONSOLE BOX

  1. B133851
    Remove the 4 <D> bolts.

  1. Disengage the 5 claws and remove the console box.


5. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Transfer)

6. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)

7. REMOVE SHIFT LEVER BOOT ASSEMBLY

C135788
  1. Remove the 4 screws and 2 clips, then remove the shift lever boot.


8. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY

C113710E04
  1. Using needle-nose pliers, remove the snap ring and pull out the shift lever from the shift lever retainer.


9. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY

F051062
  1. Separate the shift lever cap boot from the manual transmission.

  1. F051209E01
    Cover the shift lever cap with a cloth.

  1. Pressing down on the shift lever cap, turn it counterclockwise to remove the shift lever.

  1. Pull out the shift lever.


10. DRAIN MANUAL TRANSMISSION OIL
  1. Remove the drain plug and gasket and then drain the manual transmission oil.

  1. Install a new gasket and drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


11. REMOVE NO. 2 FRONT EXHAUST PIPE ASSEMBLY

  1. A129939
    Remove the 2 bolts, then remove the exhaust pipe stopper bracket. (for 4WD)

  1. A129938
    Remove the 2 bolts and 2 nuts and separate the exhaust pipe support, then remove the No. 2 front exhaust pipe.


12. REMOVE FRONT EXHAUST PIPE ASSEMBLY

  1. A128851
    Remove the 2 nuts, then remove the front exhaust pipe.

  1. Remove the front exhaust pipe gasket.


13. REMOVE PROPELLER SHAFT HEAT INSULATOR

C133778
  1. Remove the 2 bolts and remove the propeller shaft heat insulator.


14. REMOVE FRONT PROPELLER SHAFT ASSEMBLY

C098708E04
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4bolts and 4 washers.

  1. C098709E03
    Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and the propeller shaft assembly.


15. REMOVE PROPELLER SHAFT ASSEMBLY

C098699E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts and 4 washers.

  1. C098700E02
    Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and the propeller shaft assembly.


16. REMOVE NO. 2 MANIFOLD STAY

F051648
  1. Remove the 3 bolts and remove the No. 2 manifold stay.


17. REMOVE MANIFOLD STAY

F051649
  1. Remove the 3 bolts and remove the manifold stay.


18. REMOVE STARTER ASSEMBLY

  1. A128855
    Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the nut, then disconnect the wire harness from the terminal 30.

  1. A128856
    Remove the 2 bolts, then remove the starter assembly.


19. REMOVE FLYWHEEL HOUSING SIDE COVER

F050352
  1. Remove the flywheel housing side cover from the cylinder block.


20. REMOVE NO. 1 CLUTCH HOUSING COVER

F050796
  1. Remove the 3 bolts and No. 1 clutch housing cover.


21. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY

F050800
  1. Remove the 2 bolts and pull out the clutch release cylinder.


22. REMOVE ACCUMULATOR TO FLEXIBLE HOSE TUBE

C135783
  1. Using a union nut wrench, disconnect the hose tube. (for accumulator side)

  1. Remove the 3 nuts and disconnect the hose tube.

  1. C135784
    Using a union nut wrench, disconnect the hose tube. (for flexible hose side)

  1. Remove the clip


23. REMOVE CLUTCH ACCUMULATOR ASSEMBLY

C133797
  1. Using a union nut wrench, disconnect the clutch release tube from the clutch accumulator assembly.

    HINT:
    Use a container to catch the fluid.

  1. Remove the bolt and clutch release tube.

  1. C133798
    Using a union nut wrench, disconnect the flexible hose tube from the clutch accumulator assembly.

  1. Remove the nut and clutch line bracket.

  1. F050798
    Remove the 3 bolts and clutch accumulator assembly.


24. SUPPORT MANUAL TRANSMISSION WITH TRANSFER
  1. Support the manual transmission with a transmission jack.


25. REMOVE FRONT SUSPENSION MEMBER BRACKET LH

C129541
  1. Remove the 4 bolts and remove the front suspension member bracket LH.


26. REMOVE FRONT SUSPENSION MEMBER BRACKET RH

C129542
  1. Remove the 4 bolts and remove the front suspension member bracket RH.


27. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

C135785
  1. Remove the 4 bolts from the No. 3 frame crossmember sub-assembly.

  1. Remove the 4 nuts and 4 bolts and remove the No. 3 frame crossmember sub-assembly.


28. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C135786
  1. Remove the 4 bolts and engine mounting insulator rear from the manual transmission.


29. DISCONNECT CONNECTOR
  1. Tilt down the transmission.

  1. Disconnect the 2 transfer indicator switch connectors.

  1. Disconnect the speedometer sensor connector.

  1. Disconnect the back-up light switch connector.


30. DISCONNECT WIRE HARNESS

31. REMOVE MANUAL TRANSMISSION WITH TRANSFER

F051064
  1. Remove the 9 bolts.

  1. Separate and remove the manual transmission.


32. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY

C135787
  1. Remove the 5 bolts and remove the manual transmission case cover.


33. REMOVE TRANSFER ASSEMBLY
  1. Remove the 8 bolts and 2 clamps.

  1. Remove the transfer from the transmission.

← COMPONENTS (from Nov 2010)REMOVAL (Nov 2010 – Jul 2014) →