2011-2016 FJ Cruiser · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Jul 2007


1. REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

F051567
  1. Remove the 4 bolts, then remove the floor shift control shift lever retainer.

  1. D033729
    Using a plastic hammer, remove the floor shift control shift lever retainer.


2. REMOVE SHIFT LEVER HOUSING

F051568
  1. Remove the bolt, then separate the shift lever housing.


3. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY

F051569
  1. Remove the 4 bolts, then remove the transmission case cover.


4. REMOVE SHIFT DETENT BALL PLUG

F051570
  1. Using a socket hexagon wrench (10 mm), remove the shift detent ball plug from the transmission rear case.

  1. Remove the ball and compression spring from the transmission rear case.


5. REMOVE OUTPUT SHAFT ADJUST NUT
  1. Using a belt and wooden block, securely fasten the transmission to the workbench.

  1. C199431
    Using a chisel and hammer, unstake the nut.

  1. C199426E01
    Engage 5th gear, and then secure the input shaft using SST.
    SST
    09322-35010   (09322-03010, 09322-03020, 09322-03030, 90105-12087, 90170-12030, 94622-51200)

    HINT:
    1. Install SST securely so that (A) is in-line with the input shaft.
    2. Make sure that (A) moves back and forth by hand after installing SST.

  1. C199433E01
    Using handle L-type and SST, remove the nut from the output shaft.
    SST
    09326-35010   (09326-03010)

  1. Remove the belt and wooden block from the transmission.

  1. C199434
    Remove No. 2 taper roller bearing and the spacer.


6. REMOVE TRANSMISSION REAR CASE

D033738E01
  1. Remove the 10 bolts and 3 clamps.

  1. D033739
    Using a plastic hammer, carefully tap out the rear case.

    HINT:
    Place the brass bar against the rib portion of the case.


7. REMOVE MANUAL TRANSMISSION FILLER PLUG

F051572
  1. Remove the 2 transmission filler plugs and 2 gaskets from the transmission rear case.


8. REMOVE EXTENSION HOUSING OIL RECEIVER PIPE

F051573
  1. Remove the extension housing oil receiver pipe from the transmission rear case.


9. REMOVE OIL SEPARATOR PACKING SEAL

F051828
  1. Remove the oil separator packing seal from the transmission rear case.


10. REMOVE OUTPUT SHAFT REAR BEARING OUTER RACE

D033748E01
  1. Using SST, remove the 2 bearing outer races.

    SST
    09308-00010  


11. REMOVE COUNTER GEAR REAR RADIAL BALL BEARING

D033746
  1. Remove the bolt, then remove the bearing lock plate.

  1. F051574E01
    Using SST, remove the counter gear rear radial ball bearing from the transmission rear case.
    SST
    09308-00010  


12. REMOVE TRANSMISSION OIL SEPARATOR

F051575
  1. Remove the 2 bolts, then remove the oil separator.


13. REMOVE REVERSE IDLER GEAR SHAFT BOLT

D033649
  1. Remove the reverse idler gear shaft bolt from the transmission middle case.


14. REMOVE TRANSMISSION MIDDLE CASE

D033740
  1. Remove the 11 bolts, then remove the transmission middle case.

  1. D033741
    Using a plastic hammer, carefully tap out the middle case.

    HINT:
    Place the brass bar against the rib portion of the case.


15. REMOVE DRAIN PLUG SUB-ASSEMBLY

F051576
  1. Remove the drain plug and gasket from the transmission middle case.


16. REMOVE NO. 2 OIL RECEIVER PIPE

F051577
  1. Remove the No. 2 oil receiver pipe from the transmission middle case.


17. REMOVE SHIFT AND SELECT LEVER SHAFT

F051578
  1. Remove the shift and select lever shaft from the reverse gear shaft.


18. REMOVE SHIFT AND SELECT LEVER

F051579
  1. Remove the bolt, then remove the shift and select lever.

  1. Remove the lock ball pin and spring from the shift and select lever.


19. REMOVE SHIFT AND SELECT LEVER CAM

F051580
  1. Using a screwdriver, remove the E ring and the shift and select lever cam from the shift and select lever shaft.


20. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

F051581E01
  1. Using SST, remove the back-up light switch and gasket.

    SST
    09817-16011  


21. INSPECT REVERSE IDLER GEAR THRUST CLEARANCE

D033776
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)

    Maximum clearance:
    0.25 mm to (0.0098 in.)

    If the clearance exceeds the maximum, replace the reverse idler gear shaft, reverse idler gear or transmission front case.


22. REMOVE REVERSE IDLER GEAR

D033634
  1. Remove the reverse idler gear shaft, needle roller bearing and reverse idler gear.


23. INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE

D033777
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.015 to 0.050 mm (0.0006 to 0.0020 in.)

    Maximum clearance:
    0.050 mm (0.0020 in.)

    If the clearance exceeds the maximum, replace the needle roller bearing.


24. REMOVE TRANSMISSION FRONT CASE

F051582
  1. Remove the 4 bolts from the interlock bracket.

  1. F051583
    Using a hexagon wrench (27 mm), remove the plug.

  1. D033636
    Tie the input shaft, counter gear and control assembly with a piece of rope or string.

  1. D033637
    Expand the 2 snap rings, and lift up the output shaft, input shaft, counter gear and control assembly.

  1. D033638
    Remove the output shaft, input shaft, counter gear shaft and control assembly while gently tapping the clutch housing with a plastic hammer.

    NOTICE:
    Take care not to subject the output shaft, input shaft, counter gear shaft and control assembly to any impact. This could cause the ball and spring to come out.

  1. Separate the output shaft, input shaft, counter gear shaft and control assembly.


25. REMOVE NO. 1 OIL RECEIVER PIPE

F051585
  1. Remove the No. 1 oil receiver pipe from the transmission front case.


26. REMOVE FRONT BEARING SHAFT SNAP RING

D033639
  1. Using snap ring pliers, remove the 2 snap rings.


27. REMOVE TRANSMISSION CASE OIL SEAL

F051587E01
  1. Using SST, remove the transmission case oil seal from the transmission front case.

    SST
    09308-00010  


28. REMOVE NO. 3 GEAR SHIFT FORK

F051588
  1. Remove the bolt, then remove the No. 3 gear shift fork.


29. REMOVE NO. 3 GEAR SHIFT FORK SHAFT

F051829
  1. Remove the No. 3 shift fork shaft , boll, spring, No. 2 interlock pin and No. 3 interlock pin.


30. REMOVE NO. 2 GEAR SHIFT FORK

F051589
  1. Remove the bolt, then remove the No. 2 gear shift fork.


31. REMOVE NO. 2 GEAR SHIFT FORK SHAFT

F051830
  1. Remove the No. 2 shift fork shaft, ball, spring, No. 2 interlock pin and No. 3 interlock pin.


32. REMOVE NO. 1 GEAR SHIFT HEAD

D033718
  1. Using a pin punch (5 mm (0.20 in.)) and hammer, tap out the slotted pin.


33. REMOVE NO. 1 GEAR SHIFT FORK SHAFT

F051831
  1. Remove the No. 1 shift fork shaft, ball, spring, No. 1 shift head and No. 1 interlock pin.


34. REMOVE NO. 1 GEAR SHIFT FORK

D033720
  1. Using a pin punch (5 mm (0.20 in.)) and hammer, tap out the slotted pin.

  1. D033721
    Remove the No. 2 shift head and No. 1 shift fork.


35. REMOVE NO. 4 GEAR SHIFT FORK

D033722
  1. Using a pin punch (5 mm (0.20 in.)) and hammer, tap out the slotted pin.

  1. Remove the No. 4 shift fork.


36. REMOVE NO. 4 GEAR SHIFT FORK SHAFT

D033723
  1. Remove the No. 4 shift fork shaft, ball and spring.


37. REMOVE 1ST AND REVERSE SHIFT ARM

D033724
  1. Using a screwdriver, remove the E-ring.

  1. D033725
    Remove the shift arm pivot and shift arm.

← COMPONENTS (from Jul 2007)REASSEMBLY (from Jul 2007) →