2011-2016 FJ Cruiser · Service Manual ENGINE

REPLACEMENT

Removal / installation · Vehicles built Jul 2007 – Jul 2009


1. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

A072957E01
  1. Using a screwdriver with its tip wrapped in protective tape, pry out the oil seal.

    NOTICE:
    Do not damage the oil pump assembly.


2. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

A076300E02
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

    SST
    09226-10010  

  1. Apply MP grease to the oil seal lip.


3. REMOVE REAR ENGINE OIL SEAL

A076248E02
  1. Using a screwdriver and hammer, tap the oil seal out.


4. INSTALL REAR ENGINE OIL SEAL

A076268E02
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear oil seal retainer edge.

    SST
    09223-78010  

  1. Apply MP grease to the oil seal lip.


5. REMOVE VALVE GUIDE BUSH

A075616E01
  1. Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. A075617E02
    Place the cylinder head on a wooden block.

  1. Using SST, tap out the valve guide bush.

    SST
    09201-10000  
    09201-01055  
    09950-70010   (09951-07100)


6. INSTALL VALVE GUIDE BUSH

A075618E01
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Bush bore diameter:
    10.295 to 10.315 mm (0.4053 to 0.4061 in.)

    If the bush bore diameter of the cylinder head is greater than 10.315 mm (0.4061 in.), machine the bush bore to the dimension of 10.345 to 10.365 mm (0.4073 to 0.4081 in.).

    Valve guide bush diameter:
    Item
    mm (in.)
    STD
    10.333 to 10.344 (0.4068 to 0.4072)
    O/S 0.05
    10.383 to 10.394 (0.4088 to 0.4092)

  1. A075616E01
    Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. A075619E03
    Place the cylinder head on a wooden block.

  1. Using SST, tap in a new valve guide bush to the specified protrusion height.

    SST
    09201-10000  
    09201-01055  
    09950-70010   (09951-07100)

    Protrusion height:
    9.3 to 9.7 mm (0.366 to 0.382 in.)

  1. A075620E01
    Using a sharp 5.5 mm reamer, ream the valve guide bush to the standard specified clearance between the valve guide bush and valve stem.

    Standard oil clearance::
    Value guide
    Specification
    Intake
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)
    Exhaust
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)


7. REMOVE CONNECTING ROD SMALL END BUSH

EM06363E01
  1. Using SST and a press, press out the bushing.

    SST
    09222-30010  


8. INSTALL CONNECTING ROD SMALL END BUSH

A051812E01
  1. Align the oil holes of a new bushing and the connecting rod.

  1. EM06363E01
    Using SST and a press, press in the bushing.
    SST
    09222-30010  

  1. A121034E01
    Using a pin hole grinder, hone the bushing to bring the clearance between the bushing and piston pin to the specified value.

    Standard oil clearance:
    0.005 to 0.011 mm (0.0002 to 0.0004 in.)

    HINT:
    Check the measurement at room temperature. Coat the piston pin with engine oil, and push it into the connecting rod with a thumb.

← INSPECTION (from Aug 2009)REASSEMBLY (Jul 2007 – Jul 2009) →