2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1662/45 Indicator Light Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2011

DESCRIPTION

The indicator light circuit consists of the center airbag sensor assembly and the combination meter. DTC B1662/45 is set when a malfunction is detected in the indicator light circuit.
DTC No.
DTC Detecting Conditions
Trouble Areas
B1662/45
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in indicator light circuit for 2 seconds
  2. Indicator light circuit malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Combination meter
  3. Center airbag sensor assembly

WIRING DIAGRAM

C169754E01

INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch to the lock position.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connectors from the steering pad.
  5. Disconnect the connectors from the front passenger airbag assembly.
  6. Disconnect the connector from the front seat outer belt assembly LH.
  7. Disconnect the connector from the front seat outer belt assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.

1. CHECK DTC (AIRBAG SYSTEM)
  1. Turn the ignition switch to the on position.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the lock position.

  1. Turn the ignition switch to the on position and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1662/45 is not output.

    HINT:
    DTCs other than B1662/45 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK CONNECTOR (INSTRUMENT PANEL WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector and terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


3. CHECK CONNECTOR (INSTRUMENT PANEL WIRE - COMBINATION METER)
  1. Check the instrument panel wire connector and terminals (on the combination meter side) and check that the connector is properly connected to the combination meter.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector and terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


4. CHECK INSTRUMENT PANEL WIRE

  1. C127744E01
    Disconnect the connectors from the center airbag sensor assembly and combination meter.

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E13-6 (SW) - Body ground
      Ignition switch on
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E13-6 (SW) - E29-11 (LA)
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E13-6 (SW) - Body ground
      Always
      1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


5. CHECK SRS WARNING LIGHT CIRCUIT

  1. C127745E01
    Connect the instrument panel wire to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Measure the voltage.

    Standard voltage:
    Tester connection
    Switch Condition
    Specified condition
    E13-6 (SW) - Body ground .
    For 6 seconds after ignition switch turned on.
    Below 1 V
    E13-6 (SW) - Body ground .
    After 6 seconds have passed since ignition switch turned on.
    8 to 16 V



NG
Go to step 6
OK

PERFORM METER / GAUGE SYSTEM (PROBLEM SYMPTOMS TABLE)

6. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. H100897E01
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly and the combination meter.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the on position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the lock position.

  1. Turn the ignition switch to the on position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1662/45 is not output.

    HINT:
    DTCs other than B1662/45 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END


← B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction (from Aug 2012)B1662/45 Indicator Light Circuit Malfunction (Nov 2010 – Jul 2011) →