2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

INSPECTION

Inspection · Vehicles built Nov 2010 – Jul 2014

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014


INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for LHD)

  1. E127238E02
    Check the resistance of the light control switch.
    Text in Illustration 
    *a
    Component without harness connected
    (Headlight Dimmer Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      14 (T) - 16 (EL)
      OFF
      10 kΩ or higher
      13 (H) - 16 (EL)
      OFF
      10 kΩ or higher
      14 (T) - 16 (EL)
      TAIL
      Below 1 Ω
      14 (T) - 16 (EL)
      HEAD
      Below 1 Ω
      13 (H) - 16 (EL)
      HEAD
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. Check the resistance of the headlight dimmer switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      8 (HF) - 16 (EL)
      FLASH
      Below 1 Ω
      7 (HU) - 16 (EL)
      FLASH
      Below 1 Ω
      16 (EL) - 17 (HL)
      LOW BEAM
      Below 1 Ω
      7 (HU) - 16 (EL)
      HI BEAM
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. Check the resistance of the turn signal switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (TB) - 3 (TR)
      Right turn
      Below 1 Ω
      2 (TB) - 3 (TR)
      Neutral
      10 kΩ or higher
      1 (TL) - 2 (TB)
      Neutral
      10 kΩ or higher
      1 (TL) - 2 (TB)
      Left turn
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.


INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for RHD)

  1. E218750E01
    Check the resistance of the light control switch.
    Text in Illustration 
    *a
    Component without harness connected
    (Headlight Dimmer Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      9 (EL) - 14 (H)
      OFF
      10 kΩ or higher
      9 (EL) - 15 (T)
      OFF
      10 kΩ or higher
      9 (EL) - 15 (T)
      TAIL
      Below 1 Ω
      9 (EL) - 14 (H)
      HEAD
      Below 1 Ω
      9 (EL) - 15 (T)
      HEAD
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. Check the resistance of the headlight dimmer switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (HF) - 9 (EL)
      FLASH
      Below 1 Ω
      2 (HU) - 9 (EL)
      FLASH
      Below 1 Ω
      9 (EL) - 10 (HL)
      LOW BEAM
      Below 1 Ω
      2 (HU) - 9 (EL)
      HI BEAM
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. Check the resistance of the turn signal switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (TB) - 8 (TR)
      Right turn
      Below 1 Ω
      6 (TL) - 7 (TB)
      Neutral
      10 kΩ or higher
      7 (TB) - 8 (TR)
      Neutral
      10 kΩ or higher
      6 (TL) - 7 (TB)
      Left turn
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

← INSPECTION (Jul 2007 – Oct 2010)INSPECTION (from Aug 2014) →