2011-2016 FJ Cruiser · Service Manual BRAKE

CALIBRATION

Troubleshooting · Vehicles built Aug 2008 – Oct 2010

Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012


DESCRIPTION
  1. After replacing the VSC relevant components or performing "Front wheel alignment adjustment", clearing and reading the sensor calibration data are necessary.

  2. Follow the chart to perform calibration.

    Replacing Parts
    Necessary Operations
    Skid Control ECU
    Yaw rate and deceleration sensor zero point calibration.
    Yaw Rate Sensor
    1. Clearing zero point calibration data.
    2. Yaw rate and deceleration sensor zero point calibration.
    Front Wheel Alignment
    1. Clearing zero point calibration data.
    2. Yaw rate and deceleration sensor zero point calibration.


CLEAR ZERO POINT CALIBRATION (for Using an Intelligent Tester)

HINT:
After replacing the yaw rate and deceleration sensor or adjusting the front wheel alignment, be sure to clear the zero point calibration data in the skid control ECU and perform zero point calibration.

  1. Turn the ignition switch off.

  2. Check that the steering wheel is in the straight-ahead position.

  3. Automatic Transmission: Check that the shift lever is in the P position and apply the parking brake.

  4. Manual Transmission: Check that the shift lever is in neutral and apply the parking brake.

  5. Connect the intelligent tester to the DLC3.

  6. Turn the ignition switch to ON.

  7. Select the following menu items: Chassis / ABS/VSC/TRC / Reset Memory


PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR (for Using an Intelligent Tester)

HINT:
After replacing the skid control ECU and/or yaw rate and deceleration sensor, or adjusting the front wheel alignment, be sure to perform yaw rate and deceleration sensor zero point calibration.

NOTICE:
  1. While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it stationary. (Do not start the engine.)
  2. Be sure to do this on a level surface (with an inclination of less than 1 degree).

  1. Procedures for test mode.

    1. Turn the ignition switch off.

    2. Check that the steering wheel is in the straight-ahead position.

    3. Automatic Transmission: Check that the shift lever is in the P position and apply the parking brake.
      Manual Transmission: Check that the shift lever is in neutral and apply the parking brake.

      NOTICE:
      DTC C1210/36 and C1336/39 will be recorded if the shift lever is not in the P position.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch to ON.

    6. Switch the ECU to test mode using the intelligent tester.
      Select the following menu items: Chassis / ABS/VSC/TRC / Test Mode

    7. Keep the vehicle stationary on a level surface for 2 seconds or more.

    8. BR03904E81
      w/o VSC OFF Switch:
      Check that the VSC TRC warning light blinks as shown in the illustration.
      w/ VSC OFF Switch:
      Check that the SLIP indicator light blinks as shown in the illustration.

      NOTICE:
      w/o VSC OFF Switch:
      The VSC TRC warning light (and VSC OFF indicator light) stay ON when obtaining the zero point.
      w/ VSC OFF Switch:
      The SLIP indicator light stays ON when obtaining the zero point.

      HINT:
      1. If the VSC TRC warning light (*1) or SLIP indicator light (*2) does not blink, perform the zero point calibration again.
        *1: w/o VSC OFF Switch
        *2: w/ VSC OFF Switch
      2. The zero point calibration is performed only once after the system enters test mode.
      3. Calibration cannot be performed again until the stored data is cleared once.


CLEAR ZERO POINT CALIBRATION (for Using SST Check Wire)

HINT:
After replacing the yaw rate and deceleration sensor or adjusting the front wheel alignment, be sure to clear the zero point calibration data in the skid control ECU and perform zero point calibration.

  1. Turn the ignition switch to ON.

  2. F100115E85
    Using SST, connect and disconnect terminals TS and CG of the DLC3 4 times or more within 8 seconds.
    SST
    09843-18040  

  3. BR03904E91
    Check that the warning light blinks in a normal system indication pattern.


PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR (for Using SST Check Wire)

HINT:
After replacing the skid control ECU and/or yaw rate and deceleration sensor, or adjusting the front wheel alignment, be sure to perform yaw rate and deceleration sensor zero point calibration.

NOTICE:
  1. While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it stationary. (Do not start the engine.)
  2. Be sure to do this on a level surface (with an inclination of less than 1 degree).

  1. Procedures for test mode:

    1. Turn the ignition switch off.

    2. Check that the steering wheel is in the straight-ahead position.

    3. Automatic Transmission: Check that the shift lever is in the P position and apply the parking brake.
      Manual Transmission: Check that the shift lever is in neutral and apply the parking brake.

      NOTICE:
      DTC C1210/36 and C1336/39 will be recorded if the shift lever is not in the P position.

    4. F100115E85
      Using SST, connect terminals TS and CG of the DLC3.
      SST
      09843-18040  

    5. Turn the ignition switch to ON.

    6. Keep the vehicle stationary on a level surface for 2 seconds or more.

    7. BR03904E81
      w/o VSC OFF Switch:
      Check that the VSC TRC warning light blinks as shown in the illustration.
      w/ VSC OFF Switch:
      Check that the SLIP indicator light blinks as shown in the illustration.

      NOTICE:
      w/o VSC OFF Switch:
      The VSC TRC warning light (and VSC OFF indicator light) stay ON when obtaining the zero point.
      w/ VSC OFF Switch:
      The SLIP indicator light stays ON when obtaining the zero point.

      HINT:
      1. If the VSC TRC warning light (*1) or SLIP indicator light (*2) does not blink, perform the zero point calibration again.
        *1: w/o VSC OFF Switch
        *2: w/ VSC OFF Switch
      2. The zero point calibration is performed only once after the system enters test mode.
      3. Calibration cannot be performed again until the stored data is cleared once.


PERFORM INITIALIZATION OF STEERING ANGLE SENSOR (without VSC OFF Switch)

NOTICE:
Complete the adjustment of the steering wheel and wheel alignment, and then initialize the steering angle sensor. If the order is reversed, the steering wheel and wheel alignment will become misaligned.

  1. Check that the steering wheel is in the centered position.

  2. Disconnect the negative battery terminal for more than 2 seconds.

    NOTICE:
    After the ignition switch is turned off, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch off, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

  3. Reconnect the negative battery terminal.


PERFORM INITIALIZATION OF STEERING ANGLE SENSOR (with VSC OFF Switch)

NOTICE:
Complete the adjustment of the steering wheel and wheel alignment, and then initialize the steering angle sensor. If the order is reversed, the steering wheel and wheel alignment will become misaligned.

  1. Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.

  2. Check that the centered position of the steering wheel is correctly set while driving straight ahead.

    HINT:
    If front wheel alignment and steering position are adjusted as a result of abnormal centered position of the steering wheel, acquire yaw rate and acceleration sensor zero point again after the adjustments are completed.

← CALIBRATION (Jul 2007 – Jul 2008)CALIBRATION (Nov 2010 – Jul 2012) →