2011-2016 FJ Cruiser · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Jul 2007


1. REMOVE TRANSFER INDICATOR SWITCH

C133826E01
  1. Remove the indicator switches and gaskets.

    HINT:
    Indicator switch:
    No. 2
    Indicator switch (L4 position)
    No. 3
    Indicator switch (differential lock)


2. REMOVE TRANSFER GEAR SHIFT HEAD

G034493E01
  1. Using a pin punch and hammer, tap out the 2 slotted pins from the No. 1 and No. 2 gear shift heads.

  1. Remove the No. 1 and No. 2 gear shift heads from the front drive shift fork shaft and the high and low shift fork shaft.


3. REMOVE TRANSFER BEARING RETAINER SUB-ASSEMBLY

C111638
  1. Remove the 5 bolts and the bearing retainer.

    HINT:
    If necessary, tap the bearing retainer with a plastic-faced hammer to remove it.


4. REMOVE TRANSFER COVER TYPE T OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal from the bearing retainer.

    NOTICE:
    Be careful not to damage the oil seal and bearing retainer contact surfaces.


5. REMOVE TRANSFER CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

C111616
  1. Remove the 4 bolts and retainer.


6. REMOVE BREATHER OIL DEFLECTOR

7. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Front)
  1. Using a chisel and hammer, loosen the staked part of the lock nut.

  1. F043429E01
    Using SST to hold the companion flange, remove the lock nut.
    SST
    09330-00021  

  1. F043430E01
    Using SST, remove the companion flange.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)


8. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Front)
  1. Using a screwdriver and hammer, tap out the oil seal from the companion flange.

    NOTICE:
    Be careful not to damage the oil seal and companion flange contact surfaces.


9. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Rear)
  1. Remove the companion flange (rear) in the same way as the companion flange (front).

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)


10. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Rear)
  1. Using a screwdriver and hammer, tap out the oil seal from the companion flange.

    NOTICE:
    Be careful not to damage the oil seal and companion flange contact surfaces.


11. REMOVE SPEEDOMETER DRIVEN GEAR ASSEMBLY WITH VEHICLE SPEED SENSOR

G022561
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor with driven gear.


12. REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY
  1. Remove the 5 bolts and the extension housing.

    HINT:
    If necessary, tap the extension housing with a plastic-faced hammer to remove it.


13. REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal.

    NOTICE:
    Be careful not to damage the oil seal and extension housing contact surfaces.


14. REMOVE TRANSFER OUTPUT SHAFT WASHER
  1. Remove the 2 washers and the drive gear.


15. REMOVE REAR TRANSFER CASE

C116761
  1. Remove the 12 bolts and 2 clamps.

  1. Remove the rear case.

    HINT:
    If necessary, tap the rear case with a plastic-faced hammer to remove it.


16. REMOVE NO. 2 TRANSFER GEAR SHIFT FORK WITH TRANSFER HIGH AND LOW CLUTCH SLEEVE

C116762
  1. Mount the rear case in a vise.

    NOTICE:
    Place aluminum plates on the vise to prevent damage to the rear case.

  1. Using a pin punch and hammer, drive out the slotted spring pin.

  1. Using a hexagon wrench, remove the No. 1 plug.

  1. Using a magnetic finger, remove the spring and ball from the hole.

  1. Remove the No. 2 gear shift fork and high and low shift fork shaft.

  1. Using a magnetic finger, remove the straight pin.

  1. Remove the high and low clutch sleeve, 3 shifting keys and 2 No. 1 springs.


17. REMOVE CENTER DIFFERENTIAL LOCK FORK SUB-ASSEMBLY WITH FRONT DRIVE CLUTCH SLEEVE

C116763
  1. Mount the rear case in a vise.

    NOTICE:
    Place aluminum plates on the vise to prevent damage to the rear case.

  1. Using a pin punch and hammer, drive out the slotted spring pin.

  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

  1. Using a hexagon wrench, remove the No. 2 plug.

  1. Using a magnetic finger, remove the spring and ball from the hole.

  1. Remove the center differential lock fork, shift shaft stopper, 2 springs, 3 stoppers, front drive shift shaft and front drive clutch sleeve.


18. REMOVE REAR TRANSFER OUTPUT SHAFT, FRONT DRIVE CHAIN AND DRIVEN SPROCKET SUB-ASSEMBLY

C111627
  1. Mount the rear case in a vise.

    NOTICE:
    Place aluminum plates on the vise to prevent damage to the rear case.

  1. Using a snap ring expander, remove the snap ring.

  1. C116764
    Using a plastic-faced hammer, carefully tap the rear case, and remove the output shaft together with the front drive chain and driven sprocket.

  1. Remove the output shaft and driven sprocket from the front drive chain.


19. REMOVE TRANSFER DRIVEN SPROCKET BEARING

F043523
  1. Using a press, press out the bearing.

    NOTICE:
    Be careful not to drop or damage the driven sprocket.


20. REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING

F043524E01
  1. Using SST, a press and steel bar, press out the bearing.

    SST
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the driven sprocket.


21. REMOVE NO. 1 TRANSFER CASE PLUG (for Filler)
  1. Remove the filler plug and gasket.


22. REMOVE NO. 1 TRANSFER CASE PLUG (for Drain)
  1. Remove the drain plug and gasket.


23. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY

F043446
  1. Remove the 3 bolts and separator.


24. REMOVE TRANSFER CASE MAGNET

25. REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY

F043447
  1. Remove the 3 bolts and pump body.


26. REMOVE TRANSFER OIL PUMP BODY O-RING

F043462
  1. Using a screwdriver, remove the O-ring from the pump body.

    NOTICE:
    Be careful not to damage the pump body.


27. REMOVE TRANSFER OIL PUMP GEAR

F043448
  1. Remove the nut and pump gear.


28. REMOVE TRANSFER LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT

F043449
  1. Using a snap ring expander, remove the snap ring.

  1. C116765
    Remove the low planetary gear with input shaft.


29. REMOVE TRANSFER FRONT DRIVE CLUTCH SYNCHRONIZER RING

30. REMOVE OUTPUT SHAFT SPACER

C116766E01

31. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING

32. REMOVE TRANSFER CASE OIL SEAL
  1. Using a screwdriver and hammer, tap out oil seal No. 1.

  1. Using a screwdriver and hammer, tap out oil seal No. 2.

    NOTICE:
    Be careful not to damage the oil seal and front case contact surfaces.


33. REMOVE TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING

C116767
  1. Using a snap ring expander, pry out the snap ring.


34. REMOVE TRANSFER INPUT GEAR STOPPER

C116768E01

35. REMOVE TRANSFER INPUT GEAR STOPPER BALL

36. REMOVE MANUAL TRANSFER PLANETARY CARRIER WASHER

37. REMOVE TRANSFER INPUT SHAFT

C116769E01

38. REMOVE NO. 1 TRANSFER THRUST BEARING RACE

39. REMOVE TRANSFER LOW PLANETARY GEAR BEARING

40. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING

C116770
  1. Remove the 2 seal rings.


41. REMOVE TRANSFER INPUT SHAFT BEARING

F043467E01
  1. Using a snap ring expander, remove the snap ring.

  1. Using SST and a press, press out the bearing.

    SST
    09554-30011  
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the low planetary gear.


42. REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE

C116775
  1. Using a screwdriver, remove the snap ring.

    NOTICE:
    Be careful not to damage the spline piece.

  1. Remove the spline piece.


43. REMOVE TRANSFER LOW PLANETARY GEAR BEARING

F043526E01
  1. Using SST, remove the bearing.

    SST
    09612-65014   (09612-01030, 09612-01050)

    NOTICE:
    Hang SST securely between the bearing and low planetary gear.


44. REMOVE TRANSFER LOW PLANETARY RING GEAR HOLE SNAP RING

C116778E01
  1. Using a snap ring expander, remove the snap ring.


45. REMOVE NO. 2 TRANSFER OUTPUT SHAFT SPACER

46. REMOVE TRANSFER OUTPUT SHAFT SPACER BALL

47. REMOVE CENTER DIFFERENTIAL CASE

48. REMOVE TRANSFER CLUTCH HUB

C116779E01

49. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING

50. REMOVE TRANSFER OUTPUT SHAFT PLATE WASHER

51. REMOVE TRANSFER OUTPUT SHAFT REAR RADIAL BALL BEARING

C116780E01
  1. Using SST and a press, press out the bearing.

    SST
    09555-55010  


52. REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER

C116781E02

53. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

54. REMOVE TRANSFER DRIVE SPROCKET BEARING

55. REMOVE TRANSFER OUTPUT SHAFT PLATE WASHER

56. REMOVE TRANSFER CASE PLUG

F043455E01

57. REMOVE COMPRESSION SPRING

58. REMOVE TRANSFER CASE STRAIGHT PIN

59. REMOVE TRANSFER LOW PLANETARY RING GEAR

F043456
  1. Using a screwdriver, pry out the snap ring.

    NOTICE:
    Be careful not to damage the ring gear and front case.

  1. Remove the ring gear from the front case.

← REMOVAL (from Nov 2010)INSPECTION (from Jul 2007) →