2011-2016 FJ Cruiser · Service Manual DRIVE LINE

REASSEMBLY

Removal / installation · Vehicles built from Jul 2007


1. INSTALL TRANSFER LOW PLANETARY RING GEAR

F043457E01
  1. Install the ring gear onto the front case.

    NOTICE:
    Install the ring gear in the correct direction.

  1. F043456
    Using a screwdriver, install the snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed into the groove.


2. INSTALL TRANSFER CASE STRAIGHT PIN

F043455E01

3. INSTALL COMPRESSION SPRING

4. INSTALL TRANSFER CASE PLUG
  1. Apply sealant to the threads of the plug.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. Install the case plug.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }


5. INSTALL TRANSFER OUTPUT SHAFT PLATE WASHER

C116781E02

6. INSTALL TRANSFER DRIVE SPROCKET BEARING

7. INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

8. INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER

9. INSTALL REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING

C116786E01
  1. Apply gear oil to the connecting areas of the output shaft and bearing.

  1. Using SST and a press, press in a new bearing with the outer race snap ring groove facing toward the rear.

    SST
    09316-60011   (09316-00011, 09316-00071)


10. INSTALL TRANSFER OUTPUT SHAFT PLATE WASHER

C116779E01

11. INSTALL FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING

12. INSTALL TRANSFER CLUTCH HUB

13. INSTALL CENTER DIFFERENTIAL CASE

C116778E01

14. INSTALL TRANSFER OUTPUT SHAFT SPACER BALL

15. INSTALL NO. 2 TRANSFER OUTPUT SHAFT SPACER

16. INSTALL TRANSFER LOW PLANETARY RING GEAR HOLE SNAP RING
  1. Using a snap ring expander, install the snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed into the groove.


17. INSPECT TRANSFER DRIVE SPROCKET RADIAL CLEARANCE

C116787
  1. Using a dial indicator, measure the radial clearance of the drive sprocket.

    Standard clearance:
    0.01 to 0.06 mm (0.0004 to 0.0024 in.)

    Maximum clearance:
    0.06 mm (0.0024 in.)

    If the clearance is greater than the maximum, replace the drive sprocket, output shaft or needle roller bearing.


18. INSPECT TRANSFER DRIVE SPROCKET THRUST CLEARANCE

C116788
  1. Using a feeler gauge, measure the thrust clearance of the drive sprocket.

    Standard clearance:
    0.15 to 0.24 mm (0.0059 to 0.0094 in.)

    Maximum clearance:
    0.24 mm (0.0094 in.)

    If the clearance is greater than the maximum, replace the drive sprocket.


19. INSTALL TRANSFER LOW PLANETARY GEAR BEARING

C116789E01
  1. Using SST and a press, press in a new bearing.

    SST
    09950-60010   (09951-00570)
    09950-70010   (09951-07100)

    Standard depth:
    7.7 to 8.3 mm (0.303 to 0.327 in.)


20. INSTALL TRANSFER INPUT SHAFT BEARING

C116790E01
  1. Using SST and a press, press in a new bearing with the groove facing forward.

    SST
    09223-15020  
    09515-30010  
    09950-70010   (09951-07100)


21. INSTALL TRANSFER LOW PLANETARY GEAR SPLINE PIECE

C116791
  1. Using a screwdriver, install the spline piece and low planetary gear with the snap ring.

    NOTICE:
    1. Be careful not to damage the spline piece.
    2. Make sure that the snap ring is firmly installed into the groove.


22. INSTALL TRANSFER INPUT BEARING SHAFT SNAP RING

C116792
  1. Select a new snap ring that allows 0.1 mm (0.0039 in.) or less of axial free play.

    Standard snap ring thickness:
    Mark
    Thickness
    1
    1.45 to 1.50 mm (0.0571 to 0.0591 in.)
    2
    1.50 to 1.55 mm (0.0591 to 0.0610 in.)
    3
    1.55 to 1.60 mm (0.0610 to 0.0630 in.)
    4
    1.60 to 1.65 mm (0.0630 to 0.0650 in.)
    5
    1.65 to 1.70 mm (0.0650 to 0.0669 in.)

    NOTICE:
    Make sure that the snap ring is firmly installed into the groove.

  1. Using a snap ring expander, install the snap ring.


23. INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING

C116793
  1. Apply gear oil to the 2 seal rings.

  1. Install the 2 seal rings onto the input shaft.

    HINT:
    Engage the seal rings securely to eliminate clearance as shown in the illustration.


24. INSTALL TRANSFER LOW PLANETARY GEAR BEARING

C116769E01
  1. Install the bearing onto the low planetary gear.

    NOTICE:
    Install the bearing in the correct direction.


25. INSTALL NO. 1 TRANSFER THRUST BEARING RACE

26. INSTALL TRANSFER INPUT SHAFT
  1. Apply gear oil to the contact surface of the input shaft and low planetary gear.

  1. Install the input shaft onto the low planetary gear.


27. INSTALL MANUAL TRANSFER PLANETARY CARRIER WASHER

C116768E01
  1. Apply gear oil to the washer.

  1. Install the washer onto the low planetary gear.


28. INSTALL TRANSFER INPUT GEAR STOPPER BALL

29. INSTALL TRANSFER INPUT GEAR STOPPER

30. INSTALL TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING

F043514
  1. Select a new snap ring that allows 0.05 to 0.15 mm (0.0020 to 0.0059 in.) of axial free play.

    Standard snap ring thickness:
    Mark
    Thickness
    A
    2.10 to 2.15 mm (0.0827 to 0.0846 in.)
    B
    2.15 to 2.20 mm (0.0846 to 0.0866 in.)
    C
    2.20 to 2.25 mm (0.0866 to 0.0886 in.)
    D
    2.25 to 2.30 mm (0.0886 to 0.0906 in.)
    E
    2.30 to 2.35 mm (0.0906 to 0.0925 in.)
    F
    2.35 to 2.40 mm (0.0925 to 0.0945 in.)
    G
    2.40 to 2.45 mm (0.0945 to 0.0965 in.)
    H
    2.45 to 2.50 mm (0.0965 to 0.0984 in.)
    J
    2.50 to 2.55 mm (0.0984 to 0.1004 in.)
    K
    2.55 to 2.60 mm (0.1004 to 0.1024 in.)
    L
    2.60 to 2.65 mm (0.1024 to 0.1043 in.)
    M
    2.65 to 2.70 mm (0.1043 to 0.1063 in.)
    N
    2.70 to 2.75 mm (0.1063 to 0.1083 in.)
    P
    2.75 to 2.80 mm (0.1083 to 0.1102 in.)
    Q
    2.80 to 2.85 mm (0.1102 to 0.1122 in.)
    R
    2.85 to 2.90 mm (0.1122 to 0.1142 in.)
    S
    2.90 to 2.95 mm (0.1142 to 0.1161 in.)
    T
    2.95 to 3.00 mm (0.1161 to 0.1181 in.)
    U
    3.00 to 3.05 mm (0.1181 to 0.1201 in.)

  1. Using a snap ring expander, install the snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed into the groove.


31. INSTALL TRANSFER CASE OIL SEAL

F043515E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the case upper surface (No. 1).

    SST
    09316-60011   (09316-00011)

    NOTICE:
    Be careful not to damage the front case.

  1. Coat the lip of the oil seal with MP grease.

  1. C111659E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the case upper surface (No. 2).
    SST
    09304-12012  

    Standard depth:
    -0.5 to 0.5 mm (-0.020 to 0.020 in.)

    NOTICE:
    Be careful not to damage the front case.

  1. Coat the lip of the oil seal with MP grease.


32. INSTALL TRANSFER LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT

C116765
  1. Install the low planetary gear with input shaft.

    HINT:
    If necessary, heat the front case to about 50 to 80°C (122 to 176°F).

  1. F043449
    Using a snap ring expander, install the snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed into the groove.


33. INSTALL TRANSFER OIL PUMP GEAR

F043448
  1. Apply gear oil to the sliding surface of the gear.

  1. Install the gear with the nut.


34. INSTALL TRANSFER OIL PUMP BODY O-RING

F043463
  1. Coat a new O-ring with gear oil and install it onto the oil pump body.


35. INSTALL TRANSFER OIL PUMP BODY SUB-ASSEMBLY

F043447
  1. Install the pump body with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


36. INSTALL TRANSFER CASE MAGNET

F043446

37. INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY
  1. Install the oil separator with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


38. INSTALL NO. 1 TRANSFER CASE PLUG (for Filler)
  1. Install a new gasket and the filler plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


39. INSTALL NO. 1 TRANSFER CASE PLUG (for Drain)
  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


40. INSTALL TRANSFER INPUT GEAR RADIAL BALL BEARING

F043464E01
  1. Apply gear oil to the contact surfaces of the bearing and the driven sprocket.

  1. Using SST and a press, press in a new bearing.

    SST
    09316-60011   (09316-00031)

    NOTICE:
    After press-fitting the bearing to the driven sprocket, check that the bearing moves smoothly.


41. INSTALL TRANSFER DRIVEN SPROCKET BEARING

F044041
  1. Apply gear oil to the contact surfaces of the bearing and driven sprocket.

  1. Using a press, press in a new bearing.

    NOTICE:
    After press-fitting the bearing to the driven sprocket, check that the bearing moves smoothly.


42. INSTALL REAR TRANSFER OUTPUT SHAFT, FRONT DRIVE CHAIN AND DRIVEN SPROCKET SUB-ASSEMBLY

C116794
  1. Install the output shaft and driven sprocket onto the front drive chain.

  1. C116764
    Mount the rear case in a vise.

    NOTICE:
    Place aluminum plates on the vise to prevent damage to the rear case.

  1. Install the output shaft, front drive chain and driven sprocket onto the rear case.

    HINT:
    Check that the output shaft and driven sprocket turn smoothly. If necessary, heat the rear case to about 50 to 80°C (122 to 176°F).

  1. C111627
    Using a snap ring expander, install the snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed into the groove.


43. INSTALL CENTER DIFFERENTIAL LOCK FORK WITH FRONT DRIVE CLUTCH SLEEVE

C116795E01
  1. Install the clutch sleeve.

    NOTICE:
    Install the clutch sleeve in the correct direction.

  1. Install the front drive shift shaft, center differential lock fork, shift shaft stopper, 2 springs and 3 stoppers.

  1. Install the ball and spring into the hole.

  1. Apply sealant to the threads of the No. 2 plug.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. Install the No. 2 plug into the hole.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }

  1. F050152E01
    Using a pin punch and hammer, tap in the slotted pin.

    NOTICE:
    When installing the slotted pin, make sure the pin's groove (labeled A) is facing in the same direction as the shaft.


44. INSTALL NO. 2 TRANSFER GEAR SHIFT FORK WITH TRANSFER HIGH AND LOW CLUTCH SLEEVE

G021991E01
  1. Install the synchronizer ring, 3 shifting keys and 2 springs.

    NOTICE:
    1. Set the No. 1 springs so that their openings do not overlap, as shown in the illustration.
    2. Make sure that the No. 1 springs are firmly connected to the shifting keys.

  1. Install the straight pin into the hole.

  1. C117768E01
    Install the No. 2 gear shift fork, high and low shift fork shaft and high and low clutch sleeve.

    NOTICE:
    Install the fork in the correct direction.

  1. Install the ball and spring into the hole.

  1. Apply sealant to the threads of the No. 1 plug.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. Install the No. 1 plug into the hole.

  1. F050152E01
    Using a pin punch and hammer, install the slotted pin.

    NOTICE:
    When installing the slotted pin, make sure the pin's groove (labeled A) is facing in the same direction as the shaft.


45. INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING
  1. Apply gear oil to the bearing.

  1. Install the bearing onto the low planetary gear.


46. INSTALL REAR TRANSFER CASE

F043488E01
  1. Apply FIPG to the rear case as shown in the illustration.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

    NOTICE:
    If the removed rear case will be reused: After removing the case, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old FIPG on the rear case's contact surface, 2) clean off any remaining old FIPG from the rear case's contact surface, and 3) apply FIPG to the rear case.

  1. C116761
    Install the clamps and rear case with the 12 bolts.

    Torque:
    28 N*m{ 285 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Tighten the bolts of the rear case within 10 minutes of applying the FIPG. The FIPG will dry very quickly.


47. INSTALL TRANSFER OUTPUT SHAFT WASHER
  1. Install the speedometer drive gear and 2 output washers.


48. INSTALL TRANSFER EXTENSION HOUSING TYPE T OIL SEAL

F043516E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the housing upper surface.

    SST
    09223-46011  
    09631-32020  

    NOTICE:
    Be careful not to damage the extension housing.

  1. Coat the lip of the oil seal with MP grease.


49. INSTALL TRANSFER EXTENSION HOUSING SUB-ASSEMBLY

F043489E01
  1. Apply FIPG to the extension housing as shown in the illustration.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

    NOTICE:
    If the removed extension housing will be reused: After removing the housing, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old FIPG on the extension housing's contact surface, 2) clean off any remaining old FIPG from the extension housing's contact surface, and 3) apply FIPG to the extension housing.

  1. Apply sealant to the threads of the bolt.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. Install the extension housing with the 5 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the bolts of the extension housing within 10 minutes of applying the FIPG. The FIPG will dry very quickly.


50. INSTALL SPEEDOMETER DRIVEN GEAR WITH VEHICLE SPEED SENSOR

G022561
  1. Install the sensor with driven gear with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Connect the sensor connector.


51. INSTALL TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Front)

F043517E01
  1. Using SST and a hammer, tap in a new oil seal.

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to damage the companion flange.

  1. Coat the lip of the oil seal with MP grease.


52. INSTALL TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Rear)
  1. Using SST and a hammer, tap in a new oil seal (for rear) in the same way as the oil seal (for front).

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to damage the companion flange.

  1. Coat the lip of the oil seal with MP grease.


53. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Front)

F044048E02
  1. Apply gear oil to the connecting areas of the companion flange and driven sprocket.

  1. Install the companion flange onto the driven sprocket.

  1. Using SST to hold the companion flange, install a new lock nut.

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09955-04051, 09957-04010, 09958-04011)

    Torque:
    118 N*m{ 1,203 kgf*cm , 87 ft.*lbf }

  1. F050151E01
    Using a chisel and hammer, stake the lock nut to the driven sprocket.

    NOTICE:
    1. Securely stake the shaft to the lock nut's groove.
    2. Be careful not to damage parts around the lock nut.
    3. Do not apply excessive force to the shaft.


54. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Rear)
  1. Apply gear oil to the connecting area of the companion flange and output shaft.

  1. Install the companion flange onto the output shaft.

  1. Using SST to hold the companion flange, install a new lock nut.

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)

    Torque:
    118 N*m{ 1,203 kgf*cm , 87 ft.*lbf }


55. INSTALL BREATHER OIL DEFLECTOR

56. INSTALL TRANSFER CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

C111616
  1. Install the retainer with the 4 bolts.

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }


57. INSTALL TRANSFER COVER TYPE T OIL SEAL

F043518E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the retainer upper surface.

    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to damage the bearing retainer.


58. INSTALL TRANSFER BEARING RETAINER SUB-ASSEMBLY

F043490E01
  1. Apply FIPG to the bearing retainer as shown in the illustration.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

    NOTICE:
    If the removed bearing retainer will be reused: After removing the retainer, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old FIPG on the bearing retainer's contact surface, 2) clean off any remaining old FIPG from the bearing retainer's contact surface, and 3) apply FIPG to the bearing retainer.

  1. Apply sealant to the threads of the bolt.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. Install the bearing retainer with the 5 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the bolts of the bearing retainer within 10 minutes of applying the FIPG. The FIPG will dry very quickly.


59. INSTALL TRANSFER INDICATOR SWITCH

C133826E01
  1. Install new gaskets and the indicator switches.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Indicator switch:
    No. 2
    Indicator switch (L4 position)
    No. 3
    Indicator switch (differential lock)

← INSPECTION (from Jul 2007)INSTALLATION (Jul 2007 – Oct 2010) →