2011-2016 FJ Cruiser · Service Manual DRIVE LINE

INSPECTION

Inspection · Vehicles built from Aug 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012


INSPECT DIFFERENTIAL LOCK SYSTEM

  1. C270595
    Inspect the indicator light.

    1. Check that the indicator light lights up for approximately 1 second when the ignition switch is turned ON.

  1. C270596E01
    Inspect the differential lock operation.
    Text in Illustration 
    *A
    w/ CRAWL
    *B
    w/o CRAWL

    1. Jack up the vehicle then start the engine.

    2. Move the transfer shift lever to L.

    3. When the differential lock switch is turned on, check that the indicator light turns on. The differential lock is applied to the rear wheel at this time.

      HINT:
      If the gears of the differential lock system are not engaged, the indicator light remains blinking, so rotate the tires to engage the gear.

    4. When the differential lock switch is turned off, the indicator light goes off. The differential lock is released to the rear wheel at this time.

    5. C272178E01
      Check the voltage between the terminals of the four wheel drive control ECU when switching the differential control on, with the speedometer registering approximately 5 mph (8 km/h) or more.
      Text in Illustration 
      *a
      Component with harness connected
      (Four Wheel Drive Control ECU)

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (M1) - 2 (M2)
      ON
      0.5 V or less (No change)

    6. Return the differential lock switch to off.

    7. Stop the engine and lower the vehicle.


INSPECT WIRE HARNESS AND CONNECTOR

  1. C123205E05
    Inspect the system circuit with the connector disconnected.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Four Wheel Drive Control ECU)

    1. Inspect the connector according to the value(s) in the table below.

      Standard :
      Tester Connection
      Condition
      Specified Condition
      3 (M1) -2 (M2)
      Always
      Less than 100 Ω
      7 (GND) - Body ground
      Always
      Below 1 Ω
      10 (SPD) - Body ground
      Vehicle moves slowly
      1 pulse generation per 40 cm (15.75 in.)
      5 (IG) - Body ground
      Ignition switch ON with indicator light ON
      11 to 14 V
      1 (RLP) - Body ground
      Ignition switch ON with indicator light ON
      Approximately 0 V
      Ignition switch ON with indicator light OFF
      11 to 14 V
      8 (4WD) - Body ground
      Ignition switch ON with transfer shift lever except L
      Approximately 0 V
      Ignition switch ON with transfer shift lever L
      11 to 14 V
      4 (R) - Body ground
      Ignition switch ON with differential lock switch ON
      11 to 14 V
      Ignition switch ON with differential lock switch OFF
      Approximately 0 V

      HINT:
      If the result is not as specified, repair or replace the harness or connector.


INSPECT FOUR WHEEL DRIVE CONTROL ECU

  1. C272178E02
    Inspect the system circuit with the connector connected.
    Text in Illustration 
    *a
    Component with harness connected
    (Four Wheel Drive Control ECU)

    1. Turn the ignition switch to ON.

    2. Move the transfer shift lever to L.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      8 (4WD) - 7 (GND)
      -
      0.5 V or less
      1 (RLP) - 7 (GND)
      ON*
      0.5 V or less
      2 (M2) - 3 (M1)
      OFF → ON
      0.5 V or less → 11 to 14 V (Approximately 1 second) → 0.5 V or less
      2 (M2) - 3 (M1)
      ON → OFF

      HINT:
      *The rear differential should be locked mechanically.
      If the result is not as specified, replace the four wheel drive control ECU.


INSPECT DIFFERENTIAL LOCK COMPONENTS

  1. Inspect the differential lock shift actuator operation.

    1. Jack up the vehicle.

    2. Use a known good heater relay and connect it as shown below.

      C274194E01

      Text in Illustration 
      *1
      Heater Relay
      -
      -
      *a
      Component without harness connected
      (Differential Lock Shift Actuator)
      *b
      Free → Lock
      *c
      Lock → Free
      -
      -

      NOTICE:
      Connect the terminals being careful not to touch the neighboring terminals or metallic parts of the relay housing.

    3. Rotate the tire and check that the differential locks.

      1. If the operation is not as specified, replace the differential lock shift actuator.


INSPECT DIFFERENTIAL LOCK SWITCH (w/ CRAWL)

  1. C172874E07
    Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Component without harness connected
    (Differential Lock Switch)

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (E) - 4 (B)
    Pressed
    Below 1 Ω
    Not pressed
    10 kΩ or higher

    If the result is not as specified, replace the differential lock switch.


INSPECT DIFFERENTIAL LOCK SWITCH (w/o CRAWL)

  1. C270937E01
    Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Component without harness connected
    (Differential Lock Switch)

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (B) - 4 (CPU)
    Pressed
    Below 1 Ω
    Not pressed
    10 kΩ or higher

    If the value is not as specified, replace the differential lock switch.


INSPECT REAR DIFFERENTIAL LOCK INDICATOR SWITCH

  1. Inspect the rear differential lock indicator switch.

    1. C163511E13
      Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *a
      Component without harness connected
      (Rear Differential Lock Indicator Switch)
      *b
      Pushed
      *c
      Released

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 - 1
      Pushed
      Below 1 Ω
      Released
      10 kΩ or higher

      If the result is not as specified, replace the rear differential lock indicator switch.

← INSPECTION (Nov 2010 – Jul 2012)PROBLEM SYMPTOMS TABLE (Jul 2007 – Oct 2010) →