2011-2016 FJ Cruiser · Service Manual DRIVE LINE

INSPECTION

Inspection · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012


INSPECT DIFFERENTIAL LOCK SYSTEM

C135458
  1. Inspect the indicator light.

    1. Check that the indicator light lights up for approximately 1 second when the ignition switch is turned ON.

  1. Inspect the differential lock operation.

    1. Jack up the vehicle then start the engine.

    2. Shift the transfer shift lever to L position.

    3. When the differential lock control switch is set to the ON position, the indicator light is pushed on. Differential lock is applied to the rear wheel at this time.

      HINT:
      If the gears of the differential lock system are not engaged, the indicator light remains blinking, so rotate the tires to engage the gear.

    4. When the differential lock control switch is in the OFF position, the indicator light goes off. The rear differential lock is released at this time.

    5. C123204E01
      Check the voltage between the terminals of the four wheel drive control ECU when switching the differential control ON, with the speedometer registering approximately 5 mph (8 km/h) or more.

      Standard voltage:
      Switch position
      Terminal
      Specified value
      ON
      M1 - M2
      0.5 V or less (No change)

    6. Return the differential lock control switch to OFF.

    7. Stop the engine and lower the vehicle.


CHECK WIRE HARNESS AND CONNECTOR

C123205E01
  1. Inspect the system circuit with the connector disconnected.

    1. Disconnect the connector from the four wheel drive control ECU and inspect the connector on the wire harness side, as shown in the table.

      Standard :
      Tester Connection
      Trouble Part
      Condition
      Specified value
      M1 - M2
      Rear differential lock actuator
      -
      Less than 100 Ω
      GND - Body ground
      Body ground
      -
      Continuity
      SPD - Body ground
      Speed sensor
      Vehicle moves slowly
      1 pulse 40 cm (15.75 in.)
      IG - Body ground
      Differential fuse
      Ignition switch ON
      11 to 14 V
      RLP - Body ground
      Rear differential lock indicator switch
      Ignition switch ON with indicator light ON
      Approx. 0 V
      Ignition switch ON with indicator light OFF
      11 to 14 V
      4WD - Body ground
      (4WD)
      L position switch
      Ignition switch ON with transfer shift lever except L
      Approx. 0 V
      Ignition switch ON with transfer shift lever L
      11 to 14 V
      R - Body ground
      Differential lock control switch
      Ignition switch ON with differential lock control switch ON
      11 to 14 V
      Ignition switch ON with differential lock control switch OFF
      Approx. 0 V

      HINT:
      If the circuit is not as specified, check and repair or replace the trouble part shown in the table above.


CHECK 4 WHEEL DRIVE CONTROL ECU NO.2

C123206E01
  1. Inspect the system circuit with the connector connected.

    1. Turn the ignition switch to the ON position.

    2. Shift the transfer shift lever to the L position.

    3. Using a voltmeter, measure the voltage when the differential lock control switch is in the position, as shown in the table.

      Standard voltage:
      Tester connection
      Switch position
      Specified value
      4WD - GND
      -
      0.5 V or less
      RLP - GND
      ON*
      0.5 V or less
      M1 - M2
      OFF → ON
      0.5 V or less → 11 to 14 V (approx. 1 sec.) → 0.5 V or less
      M2 - M1
      ON → OFF

      HINT:
      *The rear differential should be locked mechanically.
      1. If the circuit is not as specified, replace the ECU.

    4. Install the ECU in place.


INSPECT DIFFERENTIAL LOCK COMPONENTS

  1. G022255E01
    Inspect the relay operation.

    1. Jack up the vehicle.

    2. Use a heater main relay and connect it, as shown below.

      NOTICE:
      Connect the terminals being careful not to touch the neighboring terminals or metallic parts of the relay housing.

    3. Rotate the tire and check that the differential locks.

      G022256E01

      1. If the operation is not as specified, replace the actuator.


INSPECT REAR DIFFERENTIAL LOCK SWITCH

C135467E01
  1. Inspect the differential lock switch.

    1. Inspect the resistance between terminals 1and 4.

      Standard resistance:
      Below 1 Ω

      HINT:
      If the result is not as specified, replace the switch.


INSPECT REAR DIFFERENTIAL LOCK INDICATOR SWITCH

C123210
  1. Inspect the No. 4 transfer indicator switch.

    1. Measure the resistance between the terminals when the switch is pushed (differential connected position).

      Standard resistance:
      Below 1 Ω

    2. Measure the resistance between the terminals when switch is released (differential disconnected position).

      Standard resistance:
      10 kΩ or higher

      HINT:
      If the operation is not as specified, replace the switch.

  1. Inspect the L position switch (Click here).

  1. Inspect the vehicle speed sensor (Click here).

← PARTS LOCATION (from Aug 2012)INSPECTION (Nov 2010 – Jul 2012) →