2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

CAN Main Wire for Disconnection

Circuit diagnosis · Vehicles built Aug 2009 – Oct 2010

DESCRIPTION

There may be an open circuit in the CAN main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or more.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 69 Ω or more.
  1. CAN main wire or connector
  2. ECM
  3. CAN junction connector

WIRING DIAGRAM

C133852E02

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK DLC3

  1. C118856E76
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-14 (CANL)
    Ignition switch off
    108 to 132 Ω
    A
    E1-6 (CANH) - E1-14 (CANL)
    Ignition switch off
    132 Ω or higher
    B

    Text in Illustration 
    *1
    DLC3

    NOTICE:
    When the measured value is 132 Ω or more and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "How to Proceed with Troubleshooting" (Click here) after repairing the trouble area.



B
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
A


2. CHECK CAN MAIN WIRE FOR DISCONNECTION (ECM)

  1. E192053E01
    Turn the ignition switch off.

  1. Disconnect the E81 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E81-32 (CANH) - E81-31 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to ECM)



NG
Go to step 3
OK

REPLACE ECM (Click here)

3. CONNECT CONNECTOR
  1. Reconnect the ECM connector.


NEXT


4. INSPECT CAN JUNCTION CONNECTOR

  1. C133849E05
    Turn the ignition switch off.

  1. Disconnect the E62 CAN main wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to CAN Junction Connector "A" Side (w/ Ground Terminal))

  1. C133851E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    CANH - CANL
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to CAN Junction Connector "A" Side (w/ Ground Terminal))



NG
REPLACE CAN JUNCTION CONNECTOR
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM - CAN JUNCTION CONNECTOR (CAN-H, CAN-L))


← Short to GND in CAN Bus Line (Jul 2007 – Jul 2009)Check CAN Bus Lines for Short Circuit (Aug 2009 – Oct 2010) →