2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

Short to GND in CAN Bus Line

Circuit diagnosis · Vehicles built Jul 2007 – Jul 2009

DESCRIPTION

A short to GND is suspected in the CAN bus line when there is continuity between terminals 4 (CG) and 6 (CANH) or terminals 4 (CG) and 14 (CANL) of the DLC3.
Symptoms
Trouble Area
There is continuity between terminals 4 (CG) and 6 (CANH) or terminals 4 (CG) and 14 (CANL) of the DLC3.
  1. Short to GND in CAN bus line
  2. ECM
  3. Skid control ECU
  4. Yaw rate sensor
  5. Steering angle sensor
  6. CAN J/C

WIRING DIAGRAM

C134964E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS LINE FOR SHORT TO GND (DLC3 BRANCH WIRE)

  1. C133849E02
    Turn the ignition switch OFF.

  1. Disconnect the E63 DLC3 branch wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.

  1. C118856E47
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


2. CONNECT CONNECTOR
  1. Reconnect the DLC3 branch wire connector.


NEXT


3. CHECK CAN BUS LINE FOR SHORT TO GND (SKID CONTROL ECU BRANCH WIRE)

  1. C133850E01
    Turn the ignition switch OFF.

  1. Disconnect the E66 skid control ECU branch wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.

  1. C118856E47
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG



OK
Go to step 10
NG


4. CONNECT CONNECTOR
  1. Reconnect the skid control ECU branch wire connector.


NEXT


5. CHECK CAN BUS LINE FOR SHORT TO GND (YAW RATE SENSOR BRANCH WIRE)

  1. C133849E03
    Turn the ignition switch OFF.

  1. Disconnect the E64 yaw rate sensor branch wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.

  1. C118856E47
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG



NG
Go to step 12
OK


6. CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor branch wire connector.


NEXT


7. CHECK CAN BUS LINE FOR SHORT TO GND (STEERING ANGLE SENSOR BRANCH WIRE)

  1. C133849E04
    Turn the ignition switch OFF.

  1. Disconnect the E65 steering angle sensor branch wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.

  1. C118856E47
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG



OK
Go to step 14
NG


8. CONNECT CONNECTOR
  1. Reconnect the steering angle sensor branch wire connector.


NEXT


9. CHECK CAN BUS LINE FOR SHORT TO GND (ECM MAIN WIRE)

  1. C133849E01
    Turn the ignition switch OFF.

  1. Disconnect the E62 ECM main wire connector.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.

  1. C118856E47
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG



OK
Go to step 16
NG

REPLACE CAN J/C

10. CONNECT CONNECTOR
  1. Reconnect the skid control ECU connector.


NEXT


11. CHECK CAN BUS LINE FOR SHORT TO GND (SKID CONTROL ECU BRANCH WIRE)

  1. C132867E05
    Turn the ignition switch OFF.

  1. Disconnect the A4 skid control ECU connector.

  1. C118856E47
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG



OK
REPLACE MASTER CYLINDER SOLENOID
NG

REPAIR OR REPLACE SKID CONTROL ECU BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)

12. CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor branch wire connector.


NEXT


13. CHECK CAN BUS LINE FOR SHORT TO GND (YAW RATE SENSOR BRANCH WIRE)

  1. C125957E11
    Turn the ignition switch OFF.

  1. Disconnect the E34 yaw rate sensor connector.

  1. C118856E47
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG



OK
REPLACE YAW RATE SENSOR (Click here)
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CAN-H, CAN-L)

14. CONNECT CONNECTOR
  1. Reconnect the steering angle sensor branch wire connector.


NEXT


15. CHECK CAN BUS LINE FOR SHORT TO GND (STEERING ANGLE SENSOR BRANCH WIRE)

  1. C133843E04
    Turn the ignition switch OFF.

  1. Disconnect the E16 steering angle sensor connector.

  1. C118856E47
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG



OK
REPLACE STEERING ANGLE SENSOR (Click here)
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CAN-H, CAN-L)

16. CONNECT CONNECTOR
  1. Reconnect the ECM main wire connector.


NEXT


17. CHECK CAN BUS LINE FOR SHORT TO GND (ECM MAIN WIRE)

  1. C132870E02
    Turn the ignition switch OFF.

  1. Disconnect the E46 ECM connector.

  1. C118856E47
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG



OK
REPLACE ECM (Click here)
NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CAN-H, CAN-L)


← Short to B+ in CAN Bus Line (Jul 2007 – Jul 2009)CAN Main Wire for Disconnection (Aug 2009 – Oct 2010) →