2011-2016 FJ Cruiser · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH

  1. B130749
    Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Disengage the 10 clips and remove the rear seatback board carpet.


3. REMOVE REAR SEATBACK ASSEMBLY RH

  1. B135127
    Pull up the rear seatback.

  1. Remove the bolt and the anchor plate of the rear center seat outer belt.

  1. B130750
    Remove the rear seat inner belt from the rear seatback holder.

  1. Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Remove the 2 bolts.

  1. Disengage the hook and remove the rear seatback.


4. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH

  1. B130720
    Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Disengage the 8 clips and remove the rear seatback board carpet.


5. REMOVE REAR SEATBACK ASSEMBLY LH

  1. B130721
    Remove the rear center seat inner belt from the rear seatback holder.

  1. Remove the 2 bolts.

  1. Disengage the hook and remove the rear seatback.


6. REMOVE REAR FLOOR BOARD

  1. B135073E02
    Remove the bolt and the luggage hold belt striker.

    HINT:
    Use the same procedure for both sides.

  1. B135075
    Disengage the clip and the claw and remove the rear floor board.


7. REMOVE REAR FLOOR MAT SUPPORT PLATE

  1. B130592
    Remove the 5 screws.

  1. B130593
    Disengage the 11 claws and remove the rear floor mat support plate.


8. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

HINT:
Use the same procedure for both sides.

  1. B179163E01
    Remove the cap.

  1. Remove the bolt and the luggage hold belt striker.


9. REMOVE REAR FLOOR MAT ASSEMBLY

  1. B130594
    Using a clip remover, remove the 2 clips and the rear floor mat.


10. REMOVE FRONT DOOR SCUFF PLATE RH

  1. B130597
    Disengage the 14 claws and remove the front door scuff plate.


11. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


12. REMOVE ACCESS DOOR SCUFF PLATE RH

  1. B130598
    Disengage the 6 claws and remove the access door scuff plate.


13. REMOVE ACCESS DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


14. REMOVE FRONT FLOOR FOOTREST

  1. B130586
    Disengage the 4 claws and remove the front floor footrest.


15. REMOVE FOOTREST CLIP

  1. B130587
    Remove the 2 footrest clips.


16. REMOVE COWL SIDE TRIM BOARD RH

  1. B130599
    Remove the clip.

  1. Disengage the 2 claws and remove the cowl side trim board.


17. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


18. REMOVE ROOF SIDE INNER GARNISH COVER RH

B130600E01

HINT:
Use the same procedure for both sides.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the roof side inner garnish cover.


19. REMOVE ROOF SIDE INNER GARNISH COVER LH

HINT:
Use the same procedure as for the RH side.


20. REMOVE ROOF SIDE RAIL GARNISH RH

  1. B130602
    Remove the 2 bolts.

  1. Disengage the 2 claws and remove the roof side rail garnish.


21. REMOVE ROOF SIDE RAIL GARNISH LH

HINT:
Use the same procedure as for the RH side.


22. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B130603
    Remove the front door opening trim weatherstrip.


23. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


24. REMOVE ASSIST GRIP PLUG

B175647E01

HINT:
Use the same procedure to remove all the assist grip plugs.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.


25. REMOVE ASSIST GRIP ASSEMBLY

B175648E01

HINT:
Use the same procedure to remove all the assist grips.

  1. Remove the 2 screws and the assist grip.


26. REMOVE VISOR SUB-ASSEMBLY RH

B177923E01
  1. Disengage the 2 claws and remove the visor sub-assembly.


27. REMOVE VISOR SUB-ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


28. REMOVE FRONT PILLAR GARNISH RH

  1. B130608
    Disengage the 2 clips and the claw and remove the front pillar garnish.


29. REMOVE FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.


30. REMOVE DECK SIDE GARNISH (w/ Woofer)

  1. B134992
    Disengage the 6 claws and remove the rear deck side garnish.


31. REMOVE SPEAKER MOUNTING COVER (w/ Woofer)

  1. B134991
    Disengage the 8 clips and remove the speaker mounting cover.


32. REMOVE AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)

  1. B134990
    Disconnect the speaker connector.

  1. Remove the 4 screws and the amplifier box speaker.


33. REMOVE PACKAGE HOLDER NET HOOK

B130610E02

HINT:
Use the same procedure to remove all the package holder net hooks.

  1. Remove the screw and the package holder net hook.


34. REMOVE QUARTER TRIM POCKET TRAY (w/o Woofer)

  1. B130611
    Disengage the 7 claws and remove the quarter trim pocket tray.


35. REMOVE SIDE TRIM COVER (w/o Woofer)

  1. B130612
    Disengage the 8 claws and remove the side trim cover.


36. REMOVE QUARTER TRIM POCKET (w/o Woofer)

  1. B130613
    Disengage the 6 claws and remove the quarter trim pocket.


37. REMOVE LAP BELT OUTER ANCHOR COVER

B130614E02

HINT:
Use the same procedure for both sides.

  1. Disengage the 3 claws and remove the lap belt outer anchor cover.


38. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH

  1. B130615
    Remove the bolt and the anchor plate.


39. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


40. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

  1. B130616
    Remove the 4 screws.

  1. B130617
    Disengage the 6 clips and the 8 claws and remove the deck trim side panel.


41. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

  1. B130618
    Remove the 3 screws.

  1. B130619
    Disengage the 6 clips and the 8 claws and remove the deck trim side panel.


42. REMOVE ROOF SIDE INNER GARNISH RH

  1. B130620E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.

  1. B130622
    Remove the bolt and the clip.

  1. Disengage the 7 clips and the claw and remove the roof side inner garnish.

  1. Pass the rear seat outer belt through the slit in the roof side inner garnish.


43. REMOVE ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.


44. REMOVE ROOF HEADLINING HOLE PLUG

B130623E02

HINT:
Use the same procedure for both sides.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and open the cover.

  1. B130625E02
    Remove the bolt.

  1. Disengage the claw and remove the roof headlining hole plug.


45. REMOVE COAT HOOK

B130626E02

HINT:
Use the same procedure for both sides.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.

  1. B130628E02
    Remove the bolt and the coat hook.


46. REMOVE VISOR ASSEMBLY RH

  1. B130629
    Remove the visor support shaft from the visor holder.

  1. Remove the 2 screws and the visor.


47. REMOVE VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


48. REMOVE VISOR HOLDER

B130630E02

HINT:
Use the same procedure for both sides.

  1. Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.

    HINT:
    The claw may be damaged during removal. However, it is reusable because this does not effect its function.


49. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER

B135952
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the inner rear view mirror stay holder cover.


50. REMOVE INNER REAR VIEW MIRROR ASSEMBLY

B135954
  1. Remove the 2 screws and remove the inner rear view mirror.


51. REMOVE ROOM LIGHT ASSEMBLY

B138411

HINT:
The procedure described below is for the front side. Use the same procedure for both the front and rear sides, unless otherwise specified.

  1. B138408E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.

  1. B138409E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.

    HINT:
    Use the same procedure as for the opposite side.

  1. B138410E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light.

  1. B138413E01
    for Front Side:

    1. Remove the 2 wire harnesses from the 2 claws of the room light.

    2. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.

  1. B138412E01
    for Rear Side:

    1. Remove the wire harness from the claw of the room light.

    2. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.


52. REMOVE NO. 1 PERSONAL LIGHT LENS

B205289E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the No. 1 personal light lens.


53. REMOVE NO. 2 PERSONAL LIGHT LENS

HINT:
Perform the same procedure as for the RH side.


54. REMOVE PERSONAL LIGHT ASSEMBLY

B205290E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.

  1. Disconnect the connector, and remove the personal light.


55. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B133853
    Disengage the 4 clips and 2 claws and remove the instrument panel register.

    NOTICE:
    1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
    2. Pull the instrument panel register up diagonally to remove it.


56. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

  1. B133859
    Disengage the 3 claws and separate the hood lock control lever.


57. REMOVE INSTRUMENT PANEL FINISH LOWER PANEL SUB-ASSEMBLY

  1. B133860
    Remove the 2 <F> bolts.

  1. Disengage the 5 clips and claw and remove the lower instrument panel finish panel.


58. REMOVE ROOF HEADLINING

  1. B208621
    Remove the wire harness from the 2 clamps.

  1. Disconnect the 2 connectors.

  1. Using a clip remover, remove the clamp.

  1. B208620
    Using a clip remover, remove the 3 clamps and the connector.

  1. Using a clip remover, remove the 4 clips.

    B130645

  1. B130646
    Remove the roof headlining from the back door.

← COMPONENTS (from Aug 2012)REMOVAL (Nov 2010 – Jul 2012) →