Home › BODY › INTERIOR › ROOF HEADLINING
REMOVAL
Removal / installation · Vehicles built from Aug 2012
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
1.
REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH
Pull the rear seatback lock release button and tilt the rear seatback forward.
Disengage the 10 clips and remove the rear seatback board carpet.
2.
REMOVE REAR SEATBACK ASSEMBLY RH
Pull up the rear seatback.
Remove the bolt and the anchor plate of the rear center seat outer belt.
Remove the rear seat inner belt from the rear seatback holder.
Pull the rear seatback lock release button and tilt the rear seatback forward.
Remove the 2 bolts.
Disengage the hook and remove the rear seatback.
3.
REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH
Pull the rear seatback lock release button and tilt the rear seatback forward.
Disengage the 8 clips and remove the rear seatback board carpet.
4.
REMOVE REAR SEATBACK ASSEMBLY LH
Remove the rear center seat inner belt from the rear seatback holder.
Remove the 2 bolts.
Disengage the hook and remove the rear seatback.
5.
REMOVE REAR FLOOR BOARD
Remove the bolt and the luggage hold belt striker.
Text in Illustration
*a
for RH Side
*b
for LH Side
HINT:
Use the same procedure for both sides.
Disengage the clip and the claw and remove the rear floor board.
6.
REMOVE REAR FLOOR MAT SUPPORT PLATE
Remove the 5 screws.
Disengage the 11 claws and remove the rear floor mat support plate.
7.
REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY
HINT:
Use the same procedure for both sides.
Remove the cap.
Text in Illustration
*a
for RH Side
*b
for LH Side
Remove the bolt and the luggage hold belt striker.
8.
REMOVE REAR FLOOR MAT ASSEMBLY
Using a clip remover, remove the 2 clips and the rear floor mat.
9.
REMOVE FRONT DOOR SCUFF PLATE RH
Disengage the 14 claws and remove the front door scuff plate.
10.
REMOVE FRONT DOOR SCUFF PLATE LH
HINT:
Use the same procedure as for the RH side.
11.
REMOVE ACCESS DOOR SCUFF PLATE RH
Disengage the 6 claws and remove the access door scuff plate.
12.
REMOVE ACCESS DOOR SCUFF PLATE LH
HINT:
Use the same procedure as for the RH side.
13.
REMOVE FRONT FLOOR FOOTREST (for LHD)
Disengage the 4 claws and remove the front floor footrest.
14.
REMOVE FOOTREST CLIP (for LHD)
Remove the 2 footrest clips.
15.
REMOVE COWL SIDE TRIM BOARD RH
Remove the clip.
Disengage the 2 claws and remove the cowl side trim board.
16.
REMOVE COWL SIDE TRIM BOARD LH
HINT:
Use the same procedure as for the RH side.
17.
REMOVE ROOF SIDE INNER GARNISH COVER RH
HINT:
Use the same procedure for both sides.
Text in Illustration
*1
Protective Tape
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the roof side inner garnish cover.
18.
REMOVE ROOF SIDE INNER GARNISH COVER LH
HINT:
Use the same procedure as for the RH side.
19.
REMOVE ROOF SIDE RAIL GARNISH RH
Remove the 2 bolts.
Disengage the claw and the guide and remove the roof side rail garnish.
20.
REMOVE ROOF SIDE RAIL GARNISH LH
HINT:
Use the same procedure as for the RH side.
21.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Remove the front door opening trim weatherstrip.
22.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Use the same procedure as for the RH side.
23.
REMOVE ASSIST GRIP PLUG
HINT:
Use the same procedure to remove all the assist grip plugs.
Text in Illustration
*1
Protective Tape
*a
for RH Side
*b
for LH Side
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.
24.
REMOVE ASSIST GRIP ASSEMBLY
HINT:
Use the same procedure to remove all the assist grips.
Text in Illustration
*a
for RH Side
*b
for LH Side
Remove the 2 screws and the assist grip.
25.
REMOVE VISOR SUB-ASSEMBLY RH
Disengage the 2 claws and remove the visor sub-assembly.
26.
REMOVE VISOR SUB-ASSEMBLY LH
HINT:
Use the same procedure as for the RH side.
27.
REMOVE FRONT PILLAR GARNISH RH
w/ Assist Grip:
Disengage the 2 clips and the guide and remove the front pillar garnish.
w/o Assist Grip:
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
Text in Illustration
*1
Protective Tape
Remove the bolt.
Disengage the 2 clips and the guide and remove the front pillar garnish.
28.
REMOVE FRONT PILLAR GARNISH LH
HINT:
Use the same procedure as for the RH side.
29.
REMOVE DECK SIDE GARNISH (w/ Woofer)
Disengage the 6 claws and remove the rear deck side garnish.
30.
REMOVE SPEAKER MOUNTING COVER (w/ Woofer)
Disengage the 8 clips and 2 guides and remove the speaker mounting cover.
31.
REMOVE AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)
Disconnect the connectors.
Remove the 4 screws and the amplifier box speaker.
32.
REMOVE PACKAGE HOLDER NET HOOK
HINT:
Use the same procedure to remove all the package holder net hooks.
Text in Illustration
*a
for RH Side without Woofer
*b
for LH Side
Remove the screw and the package holder net hook.
33.
REMOVE QUARTER TRIM POCKET TRAY (w/o Woofer)
Disengage the 7 claws and remove the quarter trim pocket tray.
34.
REMOVE SIDE TRIM COVER (w/o Woofer)
Disengage the 6 claws and the 2 guides and remove the side trim cover.
35.
REMOVE QUARTER TRIM POCKET (w/o Woofer)
Disengage the 6 claws and remove the quarter trim pocket.
36.
REMOVE LAP BELT OUTER ANCHOR COVER
HINT:
Use the same procedure for both sides.
Text in Illustration
*a
for RH Side
*b
for LH Side
Disengage the 3 claws and remove the lap belt outer anchor cover.
37.
REMOVE REAR SEAT OUTER BELT ASSEMBLY RH
Remove the bolt and the anchor plate.
38.
REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
HINT:
Use the same procedure as for the RH side.
39.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Remove the 3 screws and the bolt.
Disengage the 6 clips and the 8 claws and remove the deck trim side panel.
w/ Rear Power Outlet Socket:
Disconnect the 2 connectors.
40.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Remove the 3 screws.
Disengage the 6 clips and the 8 claws and remove the deck trim side panel.
41.
REMOVE ROOF SIDE INNER GARNISH RH
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
Text in Illustration
*1
Protective Tape
Remove the bolt and the clip.
Disengage the 7 clips and the guide and remove the roof side inner garnish.
Pass the rear seat outer belt through the slit in the roof side inner garnish.
42.
REMOVE ROOF SIDE INNER GARNISH LH
HINT:
Use the same procedure as for the RH side.
43.
REMOVE ROOF HEADLINING HOLE PLUG (w/ Curtain Shield Airbag)
HINT:
Use the same procedure for both sides.
Text in Illustration
*1
Protective Tape
*a
for RH Side
*b
for LH Side
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and open the cover.
Remove the bolt.
Text in Illustration
*a
for RH Side
*b
for LH Side
Disengage the claw and remove the roof headlining hole plug.
44.
REMOVE COAT HOOK
HINT:
Use the same procedure for both sides.
Text in Illustration
*1
Protective Tape
*a
for RH Side
*b
for LH Side
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
Remove the bolt and the coat hook.
Text in Illustration
*a
for RH Side
*b
for LH Side
45.
REMOVE VISOR ASSEMBLY RH
Remove the visor support shaft from the visor holder.
Remove the 2 screws and the visor.
46.
REMOVE VISOR ASSEMBLY LH
HINT:
Use the same procedure as for the RH side.
47.
REMOVE VISOR HOLDER
HINT:
Use the same procedure for both sides.
Text in Illustration
*a
for RH Side
*b
for LH Side
Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.
HINT:
The claw may be damaged during removal. However, it is reusable because this does not effect its function.
48.
REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
(Click here )
49.
REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
(Click here )
50.
REMOVE ROOM LIGHT ASSEMBLY
HINT:
The procedure described below is for the front side. Use the same procedure for both the front and rear sides, unless otherwise specified.
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.
Text in Illustration
*1
Protective Tape
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light.
Text in Illustration
*1
Protective Tape
for Front Side:
Text in Illustration
*1
Protective Tape
Remove the 2 wire harnesses from the 2 claws of the room light.
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.
for Rear Side:
Text in Illustration
*1
Protective Tape
Remove the wire harness from the claw of the room light.
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.
51.
REMOVE NO. 1 PERSONAL LIGHT LENS (w/o CRAWL)
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the No. 1 personal light lens.
Text in Illustration
*1
Protective Tape
52.
REMOVE NO. 2 PERSONAL LIGHT LENS (w/o CRAWL)
HINT:
Perform the same procedure as for the RH side.
53.
REMOVE PERSONAL LIGHT ASSEMBLY (w/o CRAWL)
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.
Text in Illustration
*1
Protective Tape
Disconnect the connector, and remove the personal light.
54.
REMOVE PERSONAL LIGHT ASSEMBLY (w/ CRAWL)
Using a moulding remover, disengage the 4 clips and 4 guides.
Disconnect the connector and remove the personal light assembly.
Text in Illustration
*1
Grommet
*2
Pin
Remove the 4 pins.
Remove the 4 grommets from the body side.
55.
REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD)
Disengage the 4 clips and 2 claws and remove the instrument panel register.
NOTICE:
To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
Pull the instrument panel register up diagonally to remove it.
56.
REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD)
Disengage the 3 claws and separate the hood lock control lever.
57.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)
Remove the 2 <E> bolts.
Disengage the 5 clips and claw and remove the lower instrument panel finish panel.
58.
REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for RHD)
Disengage the claw and separate the glove compartment door stoppers from the glove compartment door.
Text in Illustration
*1
Stopper
Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.
Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.
59.
REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY (for RHD)
Remove the screw <A>.
Disengage the 2 clips and claw and remove the instrument panel lower finish panel.
Separate the connectors from the instrument panel lower finish panel.
60.
REMOVE ROOF HEADLINING
for LHD:
Remove the wire harness from the 2 clamps.
Text in Illustration
*A
w/o CRAWL
*B
w/ CRAWL
Disconnect the 2 connectors (w/o CRAWL).
Disconnect the 3 connectors (w/ CRAWL).
Using a clip remover, disengage the clamp.
Using a clip remover, disengage the 4 clamps.
for RHD:
Using a clip remover, disengage the 2 clamps.
Disconnect the 2 connectors.
Using a clip remover, disengage the 3 clamps.
Using a clip remover, remove the 4 clips.
Remove the roof headlining from the back door.