2011-2016 FJ Cruiser · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

CAUTION:
Wear protective gloves. Sharp surfaces on the front seat adjuster could cause injuries to your hands.


1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)

NOTICE:
  1. The nuts must not be reused.
  2. Make sure that the front seat adjuster sub-assembly is not deformed. If it is, replace it with a new one.

  1. B328561
    Install the front seat side airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.


2. INSTALL SEAT POSITION SENSOR (for Driver Side)

  1. B130708
    Install the seat position sensor with the bolt.

    Torque:
    8.0 N*m{ 80 kgf*cm , 71 in.*lbf }


3. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR

  1. B130707
    Install the 2 front seat cushion edge protectors.


4. INSTALL FRONT SEAT CUSHION LOWER SHIELD RH

  1. B130706
    Engage the claw and install the front seat cushion lower shield.


5. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH

HINT:
Use the same procedure as for the RH side.


6. INSTALL RECLINING ADJUSTER OUTSIDE COVER RH

  1. B130705
    Install the reclining adjuster outside cover with the screw.


7. INSTALL RECLINING ADJUSTER OUTSIDE COVER LH

HINT:
Use the same procedure as for the RH side.


8. INSTALL RECLINING ADJUSTER INSIDE COVER RH

  1. B130703
    Engage the claw and install the reclining adjuster inside cover.

  1. Tighten the screw.


9. INSTALL RECLINING ADJUSTER INSIDE COVER LH

  1. B130704
    Engage the claw and install the reclining adjuster inside cover.

  1. w/ Front Seat Side Airbag:

    1. Install the clamp.

  1. Tighten the screw.


10. INSTALL VERTICAL SEAT ADJUSTER BUSH (for Driver Side)

  1. B135121
    Engage the claw and install the vertical seat adjuster bush.


11. INSTALL FRONT SEATBACK COVER

  1. B130700E01
    Using hog ring pliers, install the front seatback cover with 5 new hog rings.

    NOTICE:
    1. Do not soil or scratch the front seatback cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.


12. INSTALL FRONT SEATBACK ASSEMBLY

  1. B130698
    Install the front seatback.

  1. B130697E01
    w/ Front Seat Side Airbag:

    1. Fully cover the airbag with the 2 front seatback cover brackets and tighten the nut.

      Torque:
      5.5 N*m{ 55 kgf*cm , 49 in.*lbf }

      CAUTION:
      1. For vehicles with front seat side airbag, the front seatback cover must be securely installed. Otherwise, the front seat side airbag may not deploy properly.
      2. Make sure that the strap is not twisted after installing the bracket.
      3. Install the bracket securely.

  1. Using hog ring pliers, install 4 new hog rings.

  1. Install the 2 clips.

  1. B130693E01
    Fasten the 2 zippers.

  1. Using hog ring pliers, install 2 new hog rings.

  1. w/ Front Seat Side Airbag:

    1. B332546
      Insert the front seat side airbag wire harness into the front seatback cover.

  1. B130691E01
    Using hog ring pliers, install 3 new hog rings.

  1. w/ Front Seat Side Airbag:

    1. B332547
      Engage the 3 clamps to connect the front seat side airbag wire harness.


13. INSTALL FRONT SEAT HEADREST SUPPORT

B130695E01

HINT:
Use the same procedure for both sides.

  1. Align the protruding portion of the front seat headrest support with the installation groove of the front seatback frame.

  1. Engage the 2 claws and install the front seat headrest support.


14. INSTALL FRONT SEAT ARMREST ASSEMBLY (w/ Armrest)

  1. B130689E01
    Install the bush onto the front seat armrest.

  1. Install the front seat armrest with the bolt.

    Torque:
    38 N*m{ 385 kgf*cm , 28 ft.*lbf }


15. INSTALL FRONT SEAT ARMREST CAP (w/ Armrest)

  1. B130686
    Engage the 4 claws and install the front seat armrest cap.


16. INSTALL FRONT SEAT ARMREST COVER (w/ Cover)

  1. B130688
    Engage the 2 claws and install the front seat armrest cover.


17. INSTALL FRONT SEAT HEADREST ASSEMBLY

  1. B130684E01
    Push in the lock button of the front seat headrest support and install the front seat headrest.


18. INSTALL FRONT SEAT CUSHION COVER

  1. B130683E01
    Using hog ring pliers, install the front seat cushion cover with 12 new hog rings.

    NOTICE:
    1. Do not soil or scratch the front seat cushion cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.


19. INSTALL FRONT SEAT CUSHION ASSEMBLY

  1. B177951
    Engage the 2 claws and the 7 hooks and install the front seat cushion.

  1. Engage the occupant classification sensor clamp.

  1. B130680
    Install the 2 front seatback cover bands.

  1. B130701
    Install the 2 clips.


20. INSTALL FRONT SEAT CUSHION INNER SHIELD

  1. B130678
    Engage the claw and the clip and install the front seat cushion inner shield.

  1. Tighten the screw.


21. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B130778E01
    Install the front seat inner belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the front seat inner belt over the convex areas of the front seat frame adjuster.

  1. Install the wire harness into the claw of the front seat cushion inner shield.

  1. B130776
    for Driver Side:

    1. Install the 2 clamps and the 2 connectors.

    2. Connect the seat position sensor connector.

  1. B177952
    for Front Passenger Side:

    1. Install the 2 clamps and the connector.

    2. Connect the buckle switch connector.

    3. Connect the occupant classification connector.


22. INSTALL FRONT SEAT CUSHION OUTSIDE SHIELD

  1. B130676
    Engage the 2 claws and the clip and install the front seat cushion outside shield.

  1. Tighten the screw.


23. INSTALL RECLINING ADJUSTER RELEASE HANDLE

  1. B130674
    Engage the claw and install the reclining adjuster release handle.


24. INSTALL VERTICAL SEAT ADJUSTER HANDLE (for Driver Side)

  1. B130672
    Install the vertical seat adjuster handle with the 2 screws.


25. INSTALL VERTICAL SEAT ADJUSTER HANDLE COVER (for Driver Side)

  1. B130671
    Engage the 3 claws and install the vertical seat adjuster handle cover.


26. INSTALL VERTICAL SEAT ADJUSTER KNOB (for Driver Side)

  1. B130669
    Engage the snap ring and install the vertical seat adjuster knob.

← DISASSEMBLY (from Nov 2010)REASSEMBLY (from Nov 2010) →