Removal / installation · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010from Nov 2010
CAUTION:
Wear protective gloves. Sharp surfaces on the front seat adjuster could cause injuries to your hands.
HINT:
Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
1.
INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY
NOTICE:
The nuts must not be reused.
Make sure that the front seat adjuster sub-assembly is not deformed. If it is, replace it with a new one.
Install the front seat side airbag assembly with 2 new nuts.
Torque:
5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
Engage the 2 clamps.
2.
INSTALL FRONT SEATBACK ASSEMBLY
Install the front seatback.
w/ Front Seat Side Airbag:
Fully cover the airbag with the 2 front seatback cover brackets and tighten the nut.
Torque:
5.5 N*m{
55 kgf*cm
, 49 in.*lbf
}
CAUTION:
For vehicles with front seat side airbag, the front seatback cover must be securely installed. Otherwise, the front seat side airbag may not deploy properly.
Make sure that the strap is not twisted after installing the bracket.
Install the bracket securely.
Using hog ring pliers, install 4 new hog rings.
Install the 2 clips.
Fasten the 2 zippers.
Using hog ring pliers, install 2 new hog rings.
w/ Front Seat Side Airbag:
Insert the front seat side airbag wire harness into the front seatback cover.
Using hog ring pliers, install 3 new hog rings.
w/ Front Seat Side Airbag:
Engage the 3 clamps to connect the front seat side airbag wire harness.
3.
INSTALL FRONT SEAT HEADREST SUPPORT
HINT:
Use the same procedure for both sides.
Align the protruding portion of the front seat headrest support with the installation groove of the front seatback frame.
Engage the 2 claws and install the front seat headrest support.
4.
INSTALL FRONT SEAT ARMREST ASSEMBLY (w/ Armrest)
Install the bush onto the front seat armrest.
Install the front seat armrest with the bolt.
Torque:
38 N*m{
385 kgf*cm
, 28 ft.*lbf
}
5.
INSTALL FRONT SEAT ARMREST CAP (w/ Armrest)
Engage the 4 claws and install the front seat armrest cap.
6.
INSTALL FRONT SEAT ARMREST COVER (w/ Cover)
Engage the 2 claws and install the front seat armrest cover.
7.
INSTALL FRONT SEAT HEADREST ASSEMBLY
Push in the lock button of the front seat headrest support and install the front seat headrest.
8.
INSTALL FRONT SEAT CUSHION INNER SHIELD
Engage the claw and the clip and install the front seat cushion inner shield.
Tighten the screw.
9.
INSTALL FRONT SEAT INNER BELT ASSEMBLY
Install the front seat inner belt with the bolt.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
NOTICE:
Do not place the front seat inner belt over the convex areas of the front seat frame adjuster.
Install the wire harness into the claw of the front seat cushion inner shield.
for Driver Side:
Install the 2 clamps and the 2 connectors.
Connect the seat position sensor connector.
for Front Passenger Side:
Install the 2 clamps and the connector.
Connect the buckle switch connector.
Connect the occupant classification connector.
10.
INSTALL FRONT SEAT CUSHION OUTER SHIELD
Engage the 2 claws and the clip and install the front seat cushion outside shield.
Tighten the screw.
11.
INSTALL RECLINING ADJUSTER RELEASE HANDLE
Engage the claw and install the reclining adjuster release handle.
Engage the 3 claws and install the vertical seat adjuster handle cover.
14.
CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the 2 front seatback cover bands.
15.
INSTALL FRONT SEAT ASSEMBLY
NOTICE:
Follow the procedure described below in order to prevent the seat tracks from locking separately.
Insert the 2 locating pins through the 2 body holes, place the front seat in the most rearward position and make sure that the inner and outer seat tracks are locked securely.
Tighten bolt 1 and then bolt 2 onto the front side.
Torque:
37 N*m{
375 kgf*cm
, 27 ft.*lbf
}
Move the front seat to the most forward position, and then make sure that the inner and outer seat tracks are locked securely.
Tighten bolt 3 and then bolt 4 onto the rear side.
Torque:
37 N*m{
375 kgf*cm
, 27 ft.*lbf
}
Make sure that the inner and outer seat tracks lock simultaneously after the seat is moved.
HINT:
If the inner and outer seat tracks do not lock simultaneously, loosen the bolts and adjust the seat tracks.
for Driver Side:
Connect the 2 buckle switch connectors.
w/ Front Seat Side Airbag:
Connect the airbag connector.
Install the clamp.
for Front Passenger Side:
Connect the connector.
w/ Front Seat Side Airbag:
Connect the airbag connector.
Install the clamp.
16.
INSTALL FRONT SEAT TRACK COVER
HINT:
Use the same procedure for both sides.
Insert the front seat track cover 2 guides in between the seat rail and the seat leg. Then slightly lift up the front seat track cover rear part and carefully push the front seat track cover in until it cannot be pushed in any further.
Carefully insert the front seat track cover outside claw into the seat leg corner groove according to the procedure shown in the illustration.
Carefully push directly from the top of the front seat track cover inside claw to insert it into the seat leg corner groove, as shown in the illustration.