2011-2016 FJ Cruiser · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.


1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

NOTICE:
  1. The nuts must not be reused.
  2. Make sure that the front seat adjuster sub-assembly is not deformed. If it is, replace it with a new one.

  1. B328561
    Install the front seat side airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.


2. INSTALL FRONT SEATBACK ASSEMBLY

  1. B130698
    Install the front seatback.

  1. B130697E02
    w/ Front Seat Side Airbag:
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

    1. Fully cover the airbag with the 2 front seatback cover brackets and tighten the nut.

      Torque:
      5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

      CAUTION:
      1. For vehicles with front seat side airbag, the front seatback cover must be securely installed. Otherwise, the front seat side airbag may not deploy properly.
      2. Make sure that the strap is not twisted after installing the bracket.
      3. Install the bracket securely.

  1. Using hog ring pliers, install 4 new hog rings.

  1. Install the 2 clips.

  1. B130693E02
    Fasten the 2 zippers.

  1. Using hog ring pliers, install 2 new hog rings.

    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

  1. w/ Front Seat Side Airbag:

    1. B332546
      Insert the front seat side airbag wire harness into the front seatback cover.

  1. B130691E02
    Using hog ring pliers, install 3 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

  1. w/ Front Seat Side Airbag:

    1. B332547
      Engage the 3 clamps to connect the front seat side airbag wire harness.


3. INSTALL FRONT SEAT HEADREST SUPPORT

B130695E02
Text in Illustration 
*a
Protrusion
  1. Align the protruding portion of the front seat headrest support with the installation groove of the front seatback frame.

  1. Engage the 2 claws and install the front seat headrest support.

    HINT:
    Use the same procedure for both sides.


4. INSTALL ASSIST GRIP

  1. B267715
    Engage the 2 hooks and install the assist grip.

  1. Using a 5 mm hexagon wrench, install the 2 bolts.

    Torque:
    16 N*m{ 165 kgf*cm , 12 ft.*lbf }


5. INSTALL ASSIST GRIP PLUG

  1. B269207
    Engage the 2 claws and install the assist grip plug.

    HINT:
    Use the same procedure for both sides.


6. INSTALL FRONT SEAT ARMREST ASSEMBLY (w/ Armrest)

  1. B130689E02
    Install the bush onto the front seat armrest.

  1. Install the front seat armrest with the bolt.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

    Text in Illustration 
    *1
    Bush


7. INSTALL FRONT SEAT ARMREST CAP (w/ Armrest)

  1. B130686
    Engage the 4 claws and install the front seat armrest cap.


8. INSTALL FRONT SEAT ARMREST COVER (w/ Cover)

  1. B130688
    Engage the 2 claws and install the front seat armrest cover.


9. INSTALL FRONT SEAT HEADREST ASSEMBLY

  1. B130684E02
    Push in the lock button of the front seat headrest support and install the front seat headrest.
    Text in Illustration 
    *1
    Lock Button


10. INSTALL FRONT SEAT CUSHION INNER SHIELD

  1. B130678
    Engage the claw and the clip and install the front seat cushion inner shield.

  1. Tighten the screw.


11. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B130778E01
    Install the front seat inner belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the front seat inner belt over the convex areas of the front seat frame adjuster.

  1. Install the wire harness into the claw of the front seat cushion inner shield.

  1. B130776
    for Driver Side:

    1. Install the 2 clamps and the 2 connectors.

    2. Connect the seat position sensor connector.

  1. B177952
    for Front Passenger Side:

    1. Install the 2 clamps and the connector.

    2. Connect the buckle switch connector.

    3. Connect the occupant classification connector.


12. INSTALL FRONT SEAT CUSHION OUTER SHIELD

  1. B130676
    Engage the 2 claws and the clip and install the front seat cushion outside shield.

  1. Tighten the screw.


13. INSTALL RECLINING ADJUSTER RELEASE HANDLE

  1. B130674
    Engage the claw and install the reclining adjuster release handle.


14. INSTALL VERTICAL SEAT ADJUSTER HANDLE (for Driver Side)

  1. B130672
    Install the vertical seat adjuster handle with the 2 screws.


15. INSTALL VERTICAL SEAT ADJUSTER HANDLE COVER (for Driver Side)

  1. B130671
    Engage the 3 claws and install the vertical seat adjuster handle cover.


16. CONNECT SEPARATE TYPE FRONT SEATBACK COVER

  1. B130680
    Connect the 2 front seatback cover bands.


17. INSTALL FRONT SEAT ASSEMBLY

B130666E01

NOTICE:
Follow the procedure described below in order to prevent the seat tracks from locking separately.

  1. Insert the 2 locating pins through the 2 body holes, place the front seat in the most rearward position and make sure that the inner and outer seat tracks are locked securely.

  1. Tighten bolt 1 and then bolt 2 onto the front side.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat to the most forward position, and then make sure that the inner and outer seat tracks are locked securely.

  1. Tighten bolt 3 and then bolt 4 onto the rear side.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Make sure that the inner and outer seat tracks lock simultaneously after the seat is moved.

    HINT:
    If the inner and outer seat tracks do not lock simultaneously, loosen the bolts and adjust the seat tracks.

  1. B135118
    for Driver Side:

    1. Connect the 2 buckle switch connectors.

    2. w/ Front Seat Side Airbag:

      1. Connect the airbag connector.

    3. Install the clamp.

  1. B177957
    for Front Passenger Side:

    1. Connect the connector.

    2. w/ Front Seat Side Airbag:

      1. Connect the airbag connector.

    3. Install the clamp.


18. INSTALL FRONT SEAT TRACK COVER

B138598E01

HINT:
Use the same procedure for both sides.

  1. Insert the front seat track cover 2 guides in between the seat rail and the seat leg. Then slightly lift up the front seat track cover rear part and carefully push the front seat track cover in until it cannot be pushed in any further.

  1. B138599E01
    Carefully insert the front seat track cover outside claw into the seat leg corner groove according to the procedure shown in the illustration.

  1. Carefully push directly from the top of the front seat track cover inside claw to insert it into the seat leg corner groove, as shown in the illustration.


19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }


20. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    HINT:
    Some systems need initialization after reconnecting the cable to the negative battery terminal.


21. INSPECT SRS WARNING LIGHT
w/o Curtain Shield Airbag Cutoff Switch: (Click here)
w/ Curtain Shield Airbag Cutoff Switch: (Click here)
← INSTALLATION (Jul 2007 – Oct 2010)DISPOSAL (Jul 2007 – Oct 2010) →