INSTALLATION
Removal / installation · Vehicles built from Aug 2012
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
- HINT:
- The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.
| 1. INSTALL REAR SEAT OUTER BELT ASSEMBLY |
Check the angle of inclination required to lock the retractor.

Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.
- NOTICE:
- Do not disassemble the retractor.
Text in Illustration *a
Unlock
*b
Lock
Hook the lower stay of the retractor onto the 2 body hooks and provisionally install the retractor with the 2 bolts.

Tighten bolt A and then bolt B.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for bolt A
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B
Install the through anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Make sure that the shoulder anchor rotates smoothly.
Check that the ELR locks.
- NOTICE:
- Perform the check with the front seat outer belt installed.
With the belt installed, check that the belt locks when it is pulled out quickly.
If the operation is not as specified, replace the rear seat outer belt.
| 2. INSTALL ROOF SIDE INNER GARNISH |
Pass the rear seat outer belt through the slit in the roof side inner garnish.
Engage the 7 clips and the guide and install the roof side inner garnish.
Install the bolt.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
Install the clip.
Engage the claw and close the cover.

| 3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side) |
w/ Rear Power Outlet Socket:
Connect the 2 connectors.
Engage the 6 clips and the 8 claws and install the deck trim side panel.
Install the 3 screws.
Install the bolt.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
| 4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side) |
Engage the 6 clips and the 8 claws and install the deck trim side panel.
Install the 3 screws.
| 5. INSTALL LAP BELT OUTER ANCHOR COVER |
- HINT:
- Use the same procedure for both sides.
Engage the 3 claws and install the lap belt outer anchor cover.
| 6. INSTALL AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer) |
Install the amplifier box speaker with the 4 screws.
- Torque:
- 8.1 N*m{ 83 kgf*cm , 72 in.*lbf }
Connect the connectors.
| 7. INSTALL SPEAKER MOUNTING COVER (w/ Woofer) |
Engage the 8 clips and 2 guides and install the speaker mounting cover.
| 8. INSTALL DECK SIDE GARNISH (w/ Woofer) |
Engage the 6 claws and install the deck side garnish.
| 9. INSTALL QUARTER TRIM POCKET (w/o Woofer) |
Engage the 6 claws and install the quarter trim pocket.
| 10. INSTALL SIDE TRIM COVER (w/o Woofer) |
Engage the 6 claws and the 2 guides and install the side trim cover.
| 11. INSTALL QUARTER TRIM POCKET TRAY (w/o Woofer) |
Engage the 7 claws and install the quarter trim pocket tray.
| 12. INSTALL PACKAGE HOLDER NET HOOK (w/o Woofer) |
- HINT:
- Use the same procedure to install all the package holder net hooks.
Install the package holder net hook with the bolt.
- Torque:
- 8.1 N*m{ 83 kgf*cm , 72 in.*lbf }
| 13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP |
Install the front door opening trim weatherstrip.

| 14. INSTALL ACCESS DOOR SCUFF PLATE |
Engage the 6 claws and install the access door scuff plate.
| 15. INSTALL FRONT DOOR SCUFF PLATE |
Engage the 14 claws and install the door scuff plate.
| 16. INSTALL REAR FLOOR MAT ASSEMBLY |
Install the rear floor mat with the 2 clips.
| 17. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY |
- HINT:
- Use the same procedure for both sides.
Install the luggage hold belt striker with the bolt.
- Torque:
- 18 N*m{ 184 kgf*cm , 13 ft.*lbf }
Install the cap.
| 18. INSTALL REAR FLOOR MAT SUPPORT PLATE |
Engage the 11 claws and install the rear floor mat support plate.
Install the 5 screws.
| 19. INSTALL REAR FLOOR BOARD |
Engage the clip and claw and install the rear floor board.
Install the luggage hold belt striker with the bolt.

Text in Illustration *1
Guide
*a
for RH Side
*b
for LH Side
- Torque:
- 18 N*m{ 184 kgf*cm , 13 ft.*lbf }
- HINT:
- Use the same procedure for both sides.
| 20. INSTALL REAR SEATBACK ASSEMBLY (for RH Side) |
Engage the hook and temporarily install the rear seatback with the 2 bolts.

Tighten the 2 bolts in the sequence shown in the illustration.
- Torque:
- 37 N*m{ 375 kgf*cm , 27 ft.*lbf }
Pull up the rear seatback.
Install the rear seat inner belt into the rear seatback holder.

Install the anchor plate of the rear center seat outer belt with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not place the anchor plate over the convex area of the rear seat inner belt.
| 21. INSTALL REAR SEATBACK ASSEMBLY (for LH Side) |
Engage the hook and temporarily install the rear seatback with the 2 bolts.

Tighten the 2 bolts in the sequence shown in the illustration.
- Torque:
- 37 N*m{ 375 kgf*cm , 27 ft.*lbf }
Install the rear center seat inner belt into the rear seatback holder.
| 22. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH (for RH Side) |
Pull the rear seatback lock release button and tilt the rear seatback forward.

Engage the 10 clips and install the rear seatback board carpet.
Pull up the rear seatback.
| 23. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH (for LH Side) |
Engage the 8 clips and install the rear seatback board carpet.

Pull up the rear seatback.
