INSTALLATION
Removal / installation · Vehicles built from Jul 2007
| 1. INSTALL REAR NAME PLATE |
Clean the attachment surface.

Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.
- HINT:
- Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.
Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.
- NOTICE:
- Installing the rear name plate while any double-sided adhesive tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.
Using a non-residue solvent, clean the attachment surface.
Align the 2 pins and install a new rear name plate as shown in the illustration.
- Installation position:
Mark
Measurement (along surface)
a
49 mm (1.929 in.)
b
56.7 mm (2.232 in.)
- NOTICE:
- Install the rear name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the rear name plate up to 20 to 30°C (68 to 86°F) and install the rear name plate.
| 2. INSTALL NO. 2 BACK DOOR NAME PLATE |
Clean the attachment surface.

Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.
- HINT:
- Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.
Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.
- NOTICE:
- Installing the No. 2 back door name plate while any double-sided adhesive tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.
Using a non-residue solvent, clean the attachment surface.
Install a new No. 2 back door name plate as shown in the illustration.
- Installation position:
Mark
Measurement (along surface)
a
37 mm (1.457 in.)
b
14.5 mm (0.571 in.)
- NOTICE:
- Install the back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 2 back door name plate.
| 3. INSTALL NO. 1 BACK DOOR NAME PLATE |
Clean the attachment surface.

Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.
- HINT:
- Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.
Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.
- NOTICE:
- Installing the No. 1 back door name plate while any double-sided adhesive tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.
Using a non-residue solvent, clean the attachment surface.
Install a new No. 1 back door name plate as shown in the illustration.
- Installation position:
Mark
Measurement (along surface)
a
28.4 mm (1.118 in.)
b
11.5 mm (0.453 in.)
- NOTICE:
- Install the No. 1 back door name plate in an environment where the ambient temperature is over 20 °C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 1 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 1 back door name plate.
