2011-2016 FJ Cruiser · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

HINT:
The procedure described below is for the LH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. REMOVE ROOF DRIP SIDE FINISH MOULDING JOINT COVER

B135000

HINT:
Use the same procedure to remove all the roof drip moulding joint covers.

  1. Disengage the 2 claws and remove the roof drip moulding joint cover.


2. REMOVE NO. 1 ROOF DRIP SIDE FINISH MOULDING

  1. B135001
    Disengage the clip and remove the No. 1 roof drip side finish moulding.

    NOTICE:
    1. Do not remove the clip.
    2. Replace the clip with a supply clip if damaged.


3. REMOVE NO. 2 ROOF DRIP SIDE FINISH MOULDING

  1. B135003
    Remove the No. 2 roof drip side finish moulding.


4. REMOVE NO. 3 ROOF DRIP SIDE FINISH MOULDING

  1. B135005
    Remove the No. 3 roof drip side finish moulding.


5. REMOVE NO. 4 ROOF DRIP SIDE FINISH MOULDING

  1. B135007
    Disengage the clip and remove the No. 4 roof drip side finish moulding.

    NOTICE:
    1. Do not remove the clip.
    2. Replace the clip with a supply clip if damaged.


6. REMOVE WINDSHIELD OUTSIDE UPPER MOULDING SUB-ASSEMBLY

  1. B135038E02
    Apply protective tape to the roof panel in the area around the windshield outside upper moulding.
    Text in Illustration 
    *1
    Protective Tape

  1. B271502E01
    Insert the piano wires between the vehicle body and the windshield outside upper moulding, as shown in the illustration.
    Text in Illustration 
    *1
    Wooden Block

  1. Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

    NOTICE:
    When separating the windshield outside upper moulding from the vehicle, do not damage the vehicle's paintwork or exterior ornaments.

  1. B267589
    Disengage the 4 claws and the 2 clips and remove the windshield outside upper moulding.


7. REMOVE ROOF DRIP SIDE FINISH MOULDING RETAINER

B135040

HINT:
Use the same procedure to remove all the roof drip side finish moulding retainers.

  1. Remove the screw and the roof drip side finish moulding retainer.


8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:
Use the same procedure as for the RH side (Click here).


9. REMOVE ASSIST GRIP PLUG

HINT:
Use the same procedure as for the RH side (Click here).


10. REMOVE ASSIST GRIP ASSEMBLY

HINT:
Use the same procedure as for the RH side (Click here).


11. REMOVE FRONT PILLAR GARNISH

HINT:
Use the same procedure as for the RH side (Click here).


12. REMOVE FRONT PILLAR OUTER GARNISH

  1. B135013
    Remove the nut.

  1. Disengage the 5 clips and remove the front pillar outer garnish.


13. REMOVE ROOF SIDE GARNISH PROTECTOR

  1. B135014E02
    Using a clip remover, remove the 4 clips.
    Text in Illustration 
    *1
    Double-sided Adhesive Tape

  1. Remove the 3 pieces of double-sided adhesive tape and the roof side garnish protector.

← REMOVAL (Jul 2007 – Oct 2010)REMOVAL (from Aug 2012) →