2011-2016 FJ Cruiser · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built Jul 2007 – Jul 2008

Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Jul 2011 from Aug 2011


1. INSTALL HOLE PLUG
  1. Install the 2 hole plugs.


2. INSTALL CUSHION
  1. Install the 2 cushions.


3. INSTALL REAR NAME PLATE

  1. B134748E01
    Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the rear name plate while any double-sided adhesive tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Align the 2 pins and install a new rear name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    49 mm (1.929 in.)
    b
    56.7 mm (2.232 in.)

    NOTICE:
    Install the rear name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the rear name plate up to 20 to 30°C (68 to 86°F) and install the rear name plate.


4. INSTALL NO. 2 BACK DOOR NAME PLATE

  1. B134745E01
    Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 2 back door name plate while any double-sided adhesive tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 2 back door name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    37 mm (1.457 in.)
    b
    14.5 mm (0.571 in.)

    NOTICE:
    Install the back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 2 back door name plate.


5. INSTALL NO. 1 BACK DOOR NAME PLATE

  1. B134742E01
    Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 1 back door name plate while any double-sided adhesive tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 1 back door name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    28.4 mm (1.118 in.)
    b
    11.5 mm (0.453 in.)

    NOTICE:
    Install the No. 1 back door name plate in an environment where the ambient temperature is over 20 °C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 1 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 1 back door name plate.


6. INSTALL BACK DOOR DAMPER STAY LOWER BRACKET

  1. B135999
    Install the back door damper stay lower bracket with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }


7. INSTALL BACK DOOR SUPPORT

B135599
  1. Install the 2 stop rings onto the back door support.

  1. Install the back door support.


8. INSTALL BACK DOOR STAY UPPER BRACKET LH

  1. B135593
    Install the back door stay upper bracket with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


9. INSTALL BACK DOOR STAY UPPER BRACKET RH

  1. B135592
    Install the back door stay upper bracket with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


10. INSTALL NO. 2 BACK DOOR WEATHERSTRIP

  1. B135591
    Install the No. 2 back door weatherstrip.


11. INSTALL BACK DOOR HINGE ASSEMBLY RH

  1. B135998
    Install the back door hinge with the bolt.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }


12. INSTALL BACK DOOR HINGE ASSEMBLY LH

HINT:
Use the same procedure as described for the RH side.


13. INSTALL BACK DOOR OUTSIDE HANDLE
  1. Install the bush.

  1. B139406
    Install the back door outside handle with the screw.


14. INSTALL BACK WINDOW LOCK STRIKER ASSEMBLY

B139405
  1. Install the back window lock striker and retainer with the 2 screws.


15. INSTALL BACK WINDOW STAY UPPER BRACKET RH

B139404
  1. Install the back window stay upper bracket and retainer with the 2 screws.


16. INSTALL BACK WINDOW STAY UPPER BRACKET LH

HINT:
Use the same procedure as described for the RH side.


17. INSTALL BACK DOOR GLASS

B139403
  1. Install the back door glass with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the 2 connectors.


18. INSTALL BACK WINDOW SUPPORT LH

B135551
  1. Install the 2 stop rings onto the back window support.

  1. Install the back window support.


19. INSTALL BACK WINDOW SUPPORT RH

HINT:
Use the same procedure as described for the LH side.


20. INSTALL BACK DOOR SIDE FEMALE STOPPER SUB-ASSEMBLY

  1. B135549
    Install the back door side female stopper with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


21. INSTALL HIGH MOUNTED STOP LIGHT ASSEMBLY

  1. B135165
    Install the high mounted stop light with the 2 screws.


22. INSTALL REAR SPOILER

  1. B135163
    Install the rear spoiler with the 4 nuts.

  1. B135162
    w/ Rear Wiper:

    1. Connect the washer hose.

  1. Install the washer hose into the claw of the rear spoiler.

  1. Install the 3 clamps.

  1. Connect the high mounted stop light connector.


23. INSTALL NO. 1 REAR SPOILER COVER

  1. B135550
    Install the No. 1 rear spoiler cover with the 4 screws.


24. INSTALL BACK DOOR LOCK CYLINDER ASSEMBLY

  1. B135548
    Install the back door lock cylinder with the retainer.

  1. B135547
    Connect the connector and the 2 clamps.


25. INSTALL BACK DOOR LOCK ASSEMBLY

  1. B135519E01
    Apply MP grease to the sliding and rotating areas of the back door lock.

  1. Using "Torx" socket wrench T30, install the back door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Tighten bolt A.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.

  1. B135518
    Connect the back door lock rod as shown in the illustration.


26. INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

  1. B135114
    Engage the 4 clips and install the back door outside garnish.

  1. B135111
    Tighten the 2 nuts.

    Torque:
    6.0 N*m{ 60 kgf*cm , 53 in.*lbf }

  1. B135110
    Connect the back door lock rod.

  1. Connect the license light connector.

  1. B135109
    Engage the 4 claws and install the plug hole.

  1. B135112E01
    Remove the protective tape.


27. INSTALL BACK WINDOW LOCK ASSEMBLY

  1. B135521
    Install the back window lock with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector and clamp.


28. INSTALL MULTIPLEX NETWORK DOOR ECU

  1. B135545
    Install the multiplex network door ECU with the 2 screws.

  1. Connect the 3 connectors and 2 harness clamps.


29. INSTALL REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

30. INSTALL REAR WIPER MOTOR (w/ Rear Wiper)

  1. E127890
    Install the rear wiper motor with the 3 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.


31. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E129609E01
    Install the rear wiper arm in the position shown in the illustration with the nut.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }

    HINT:
    Using the nut, Tighten the rear wiper arm with the slider on the linear wiper step, 20 mm below the rise-up position in the rotational direction.

  1. Return the slider to the rise-up position.

  1. E129608
    Close the rear wiper arm head cap.


32. INSTALL BACK DOOR SERVICE HOLE COVER

  1. B135595
    Apply butyl tape to the door panel, then install the new back door service hole cover as shown in the illustration.

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.


33. INSTALL BACK DOOR TRIM BOARD

  1. B135554
    Engage the 16 clips and install the back door trim board.

  1. Install the 2 screws.


34. INSTALL DOOR TRIM RETAINER CAP

  1. B135553
    Engage the 2 claws and install the door trim retainer cap.


35. INSTALL BACK DOOR TRIM COVER RH

B139382
  1. Engage the 3 claws and back door trim cover.


36. INSTALL BACK DOOR TRIM COVER LH

HINT:
Use the same procedure as described for the RH side.


37. INSTALL SPARE WHEEL CARRIER BRACKET SUB-ASSEMBLY

  1. B135543
    Install the spare wheel carrier bracket with the 2 bolts and 2 nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


38. INSTALL BACK DOOR OUTSIDE MOULDING RH

  1. B135032
    Install 6 new clips in the positions shown in the illustration.

    NOTICE:
    If you install the clips wrongly, the installation of the back door outside moulding will be improper.

  1. B135031
    Engage the 6 clips and install the back door outside moulding.

  1. B135029E01
    Tighten the screw.

  1. Remove the protective tape.


39. INSTALL BACK DOOR OUTSIDE MOULDING LH

  1. B135028
    Install 6 new clips in the positions shown in the illustration.

    NOTICE:
    If you install the clips wrongly, the installation of the back door outside moulding will be improper.

  1. B135027
    Engage the 6 clips and install the back door outside moulding.

  1. B135025E01
    Tighten the screw.

  1. Remove the protective tape.


40. INSTALL SPARE DISC WHEEL

Torque:
88 N*m{ 897 kgf*cm , 65 ft.*lbf }


41. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

← ADJUSTMENT (from Jul 2007)REASSEMBLY (Aug 2008 – Jul 2011) →