INSTALLATION
Removal / installation · Vehicles built from Aug 2012
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
| 1.
INSTALL UNLOCK WARNING SWITCH |
 |
- Install the unlock warning switch onto the steering column bracket upper.
Connect the connector.
| 2.
INSTALL KEY INTER LOCK SOLENOID (for Automatic Transmission) |
 |
- Install the key inter lock solenoid with the 2 screws.
- Install the clamp onto the steering column bracket upper.
| 3.
INSTALL IGNITION SWITCH LOCK CYLINDER AND KEY SET |
 |
- Make sure that the ignition switch lock cylinder is in the ACC position.
Install the ignition switch lock cylinder.
| 4.
INSTALL INSTRUMENT PANEL FINISH PANEL END LH
|
 |
Engage the 3 claws and install the instrument panel finish panel end.
| 5.
INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
|
 |
Install the lower instrument panel with the 2 <B> bolts, 2 <D> bolts, 7 <C> bolts and nut <F>.


-
Torque:
- 20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
for bolt <B>
Engage the clamps and connect the connectors.
| 6.
CONNECT PASSENGER AIRBAG CONNECTOR
|
 |
Connect the passenger airbag connector.
| 7.
INSTALL ASSIST GRIP RETAINER RH (w/ Assist Grip)
|
 |
Install the assist grip retainer with the 2 bolts.
-
Torque:
- 29 N*m{
296 kgf*cm
, 21 ft.*lbf
}
| 8.
INSTALL ASSIST GRIP RETAINER LH (w/ Assist Grip)
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 9.
INSTALL FRONT NO. 2 SPEAKER ASSEMBLY
|
 |
- Connect the speaker connector.
Insert the 2 hooks into the 2 instrument panel holes and install the front speaker with the 2 bolts.
-
Torque:
- 2.5 N*m{
25 kgf*cm
, 22 in.*lbf
}
| 10.
INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
|
 |
Engage the 4 clips and claw and install the instrument panel speaker panel.
| 11.
INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 12.
INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
|
 |
Engage the 4 clips and 2 claws and install the instrument panel register.
Install the bolt and clip.
- Engage the 2 claws and install the instrument panel hole cover.
| 13.
INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH
|
 |
Install the connectors to the instrument panel lower finish panel.
Engage the claw and 2 clips and install the instrument panel lower finish panel.
Install the screw <A>.
| 14.
INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
|
 |
- Install the glove compartment door assembly with the 3 hinges while holding it horizontal.
Slightly flex the upper part of the glove compartment door assembly, and install the glove compartment door assembly.
Install the glove compartment door stoppers onto the glove compartment door.
| 15.
INSTALL COMBINATION METER ASSEMBLY
|
 |
Connect the 2 connectors and the clamp.
Install the combination meter assembly with the 4 screws.
-
Torque:
- 7.0 N*m{
71 kgf*cm
, 62 in.*lbf
}
| 16.
INSTALL INSTRUMENT CLUSTER LOWER FINISH PANEL
|
 |
Connect the connectors.
Engage the 3 clips and the 4 claws and install the instrument cluster lower finish panel.
| 17.
INSTALL LOWER INSTRUMENT PANEL LH
|
 |
Install the lower instrument panel with the 4 <E> bolts.
| 18.
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
|
 |
Engage the 5 clips and claw and install the lower instrument panel finish panel.
Install the 2 <E> bolts.
| 19.
INSTALL INSTRUMENT PANEL FINISH PLATE
|
 |
- Install the instrument panel finish plate.
Text in Illustration
*1
|
Instrument Panel Finish Plate
|
| 20.
INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
|
 |
Engage the 3 claws and install the hood lock control lever.
| 21.
INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
|
 |
Engage the 4 clips and 2 claws and install the instrument panel register.
| 22.
INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY
|
 |
Engage the 3 clips and 2 claws and install the instrument lower cover.
Install the 2 <E> bolts and 2 clips.
| 23.
INSTALL CONSOLE UPPER PANEL NO. 1 GARNISH
|
 |
- Slide the console upper panel garnish toward the front of the vehicle and engage guide.
Engage the claw and clip and install the console upper panel garnish.
| 24.
INSTALL FRONT CONSOLE BOX ASSEMBLY
|
 |
Engage the 5 guides and install the front console box.
Install the 4 <H> bolts.
| 25.
INSTALL BOX BOTTOM MAT
|
 |
Install the box bottom mat.
| 26.
INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY
|
 |
Engage the 3 guides and 5 clips and install the console upper rear panel.
| 27.
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD)
|
 |
- Install the shift lever knob.
| 28.
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)
|
 |
- Install the shift lever knob.
| 29.
INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY
|
 |
- Slide the parking brake hole cover toward the rear of the vehicle and engage the 2 guides.
Engage the 4 claws and install the parking brake hole cover.
| 30.
INSTALL RADIO RECEIVER ASSEMBLY
|
 |
- Connect the connectors.
Align the 2 bosses of the radio bracket with the hole in the instrument panel and install the radio receiver with the 4 bolts.
-
Torque:
- 2.5 N*m{
25 kgf*cm
, 22 in.*lbf
}
| 31.
INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY
|
 |
Connect the 3 connectors.
Engage the 4 clips and install the integration control panel assembly.
Install the 2 screws.
| 32.
INSTALL INSTRUMENT PANEL GARNISH LH
|
 |
Engage the 3 clips and install the instrument panel garnish.
Install the screw <G>.
| 33.
INSTALL INSTRUMENT PANEL GARNISH RH
|
 |
Engage the 3 clips and install the instrument panel garnish.
Install the screw <G>.
| 34.
INSTALL FRONT PILLAR GARNISH RH
|
 |
w/ Assist Grip:
Engage the guide and the 2 clips and install the front pillar garnish.
w/o Assist Grip:
Engage the guide and the 2 clips and install the front pillar garnish.
Install the bolt.
- Engage the claw and close the cover.
| 35.
INSTALL FRONT PILLAR GARNISH LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 36.
INSTALL ASSIST GRIP ASSEMBLY (w/ Assist Grip)
|
 |
- HINT:
- Use the same procedure to install all the assist grips.
Install the assist grip with the 2 bolts.
-
Torque:
- 8.0 N*m{
82 kgf*cm
, 71 in.*lbf
}
| 37.
INSTALL ASSIST GRIP PLUG (w/ Assist Grip)
|
 |
- HINT:
- Use the same procedure to install all the assist grip plugs.
Text in Illustration
*a
|
for RH Side
|
*b
|
for LH Side
|
Engage the 2 claws and install the assist grip plug.
| 38.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
|
 |
Install the front door opening trim weatherstrip.
| 39.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
|
 |
Install the front door opening trim weatherstrip.
| 40.
INSTALL COWL SIDE TRIM BOARD RH
|
 |
Engage the 2 claws and install the cowl side trim board.
Install the clip.
| 41.
INSTALL COWL SIDE TRIM BOARD LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 42.
INSTALL FOOTREST CLIP
|
 |
- HINT:
- Use the same procedure for both sides.
Engage the 2 claws and install the footrest clip.
| 43.
INSTALL FRONT FLOOR FOOTREST
|
 |
- Engage the 2 studs and install the front floor footrest.
| 44.
INSTALL FRONT DOOR SCUFF PLATE RH
|
 |
Engage the 14 claws and install the door scuff plate.
| 45.
INSTALL FRONT DOOR SCUFF PLATE LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 46.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
 |
-
Torque:
- 3.9 N*m{
40 kgf*cm
, 35 in.*lbf
}
| 47.
INSPECT SRS WARNING LIGHT |
 |
(Click here)