2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. REMOVE FRONT DOOR SCUFF PLATE LH

  1. A130151
    Disengage the 14 claws and remove the front door scuff plate.


3. REMOVE REAR DOOR SCUFF PLATE LH

  1. A130152
    Disengage the 6 claws and remove the rear door scuff plate.


4. REMOVE REAR SEAT CUSHION ASSEMBLY LH

  1. A129905
    Remove the 2 bolts, then remove the rear seat cushion LH.


5. REMOVE REAR FLOOR SERVICE HOLE COVER

  1. A129907
    Pull back the floor carpet.

  1. Remove the center floor silencer pad LH.

  1. A129904
    Remove the 3 screws from the center floor.

  1. A129908
    Disconnect the connector.


6. DISCONNECT FUEL TANK TO FILLER PIPE HOSE

  1. A075955
    Loosen the clamp bolt and disconnect the fuel tank to filler pipe hose.


7. REMOVE NO.1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Automatic Transmission)

  1. A137217
    Remove the 2 nuts and the fuel tank protector bracket.

  1. A129913
    Remove the 4 nuts and the fuel tank protector.


8. REMOVE NO.1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Manual Transmission)

  1. A138100
    Remove the nut and the fuel tank protector bracket.

  1. A129913
    Remove the 4 nuts and the fuel tank protector.


9. DISCONNECT FUEL TANK MAIN TUBE AND FUEL TANK RETURN TUBE

  1. A226908E01
    Pinch the retainer to disengage the lock claws and pull out the fuel tank return tube.
    Text in Illustration 
    *1
    Retainer
    *2
    O-Ring
    *a
    Lock
    *b
    Unlock

    NOTICE:
    1. Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
    2. Do not use any tools in this work.
    3. Do not bend or twist the nylon tube.
    4. To protect the tube, cover it with a vinyl bag after disconnecting it.
    5. When the connector and the pipe are stuck, turn the retainer carefully to disconnect them.


10. DISCONNECT FUEL CUT-OFF TUBE

  1. A226916E01
    Turn the retainer to disengage the lock claws and pull out the fuel cut off tube.
    Text in Illustration 
    *1
    Retainer
    *2
    O-Ring
    *3
    Fuel Pipe
    *4
    Nylon Tube
    V100135
    Turn
    V100136
    Pull

    NOTICE:
    1. Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
    2. Do not use any tools in this work.
    3. Do not bend or twist the nylon tube.
    4. To protect the tube, cover it with a vinyl bag after disconnecting it.
    5. When the connector and the pipe are stuck, turn the retainer carefully to free and then disconnect the fuel tank tube.


11. DISCONNECT FUEL TANK BREATHER TUBE

  1. A226909E01
    Disconnect the fuel tank breather tube from the fuel tank.
    Text in Illustration 
    V100135
    Pinch
    V100136
    Push

    1. Push the connector firmly.

    2. Pinch portion A, as shown in the illustration.

    3. Pull out the connector.


12. REMOVE FUEL TANK ASSEMBLY
  1. Hold the fuel tank using a mission jack.

  1. A129914
    Remove the 2 fuel tank bands.

    1. Remove the 2 bolts.

    2. Remove the 2 clips and 2 pins, then remove the 2 fuel tank bands.


13. REMOVE FUEL TANK MAIN TUBE AND FUEL TANK RETURN TUBE

  1. A172198E02
    Remove the 2 joint clips, and pull out the 2 fuel tank tubes.
    Text in Illustration 
    *1
    O-Ring
    V100135
    Pull

    NOTICE:
    1. Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
    2. Do not use any tools in this work.
    3. Do not bend or twist the nylon tube by force.
    4. After disconnecting, cover the fuel tube joint with a vinyl bag.
    5. When the fuel tube joint and fuel suction plate are stuck, turn the fuel tank main tube carefully to free and then disconnect it. Likewise, disconnect the fuel tank return tube.


14. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

NOTICE:
Protect the connector and tube joint with masking tape or equivalent to prevent any foreign matter from sticking to them. Clean any dirt and foreign matter from the fuel suction tube assembly before removing.

  1. A076683E01
    Using a SST, loosen the retainer.
    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    Align the tips of the SST with the ribs on the retainer.

  1. Remove the retainer.

  1. Pull the fuel pump assembly out of the fuel tank.

    NOTICE:
    Do not bend the arm of the sender gauge.

  1. A172212
    Remove the gasket from the fuel tank.

← COMPONENTS (from Aug 2009)REMOVAL (from Aug 2009) →