INSTALLATION
Removal / installation · Vehicles built Aug 2009 – Oct 2012
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2012 from Nov 2012
| 1. INSTALL FUEL TANK TO FILLER PIPE HOSE |
Connect a new fuel tank to filler pipe hose, as shown in the illustration, with the clamp.

| 2. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
Install a new gasket onto the fuel tank.

Set the fuel suction tube assembly to the fuel tank.
- NOTICE:
- Do not bend the arm of the fuel sender gauge.
Fit the spline of the fuel suction tube assembly into the keyway of the fuel tank.
Install a new retainer.
Align the mark on a new retainer with the rib on the fuel tank as shown in the illustration.

*1
Start Mark (Fuel Tank Side)
*2
Start Mark (Retainer Side)
Using SST, turn the retainer 740° to 760° clockwise (more than 2 turns), and position the mark on the retainer within range A to install it.

*1
Fuel Tank Side Mark
*2
Retainer Side Mark
- SST
- 09808-14020
(09808-01410, 09808-01420, 09808-01430)
- HINT:
- Align the tips of the SST with the ribs on the retainer.
| 3. INSTALL FUEL TANK MAIN TUBE AND FUEL TANK RETURN TUBE |
Install the fuel tank main tube and return tube with the 2 joint clips.

Text in Illustration *1
O-Ring


Push
- NOTICE:
- Check that there are no scratches or foreign matter around the disconnected part of the fuel tube joint and plug before performing this work.
- Check that the fuel tube joint is securely inserted into the end.
- Check that the tube joint clips are on the collar of the fuel tube joint.
- After installing the tube joint clip, check that the fuel tank main tube and return tube can be pulled out.
- Check that there are no scratches or foreign matter around the disconnected part of the fuel tube joint and plug before performing this work.
| 4. INSTALL FUEL TANK CUSHION |
Install 4 new fuel tank cushions onto the fuel tank.
| 5. INSTALL NO. 3 FUEL TANK PROTECTOR |
Install the No. 3 fuel tank protector with the 2 bolts and 3 claws.
- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
| 6. INSTALL FUEL TANK ASSEMBLY |
Set a mission jack onto the fuel tank.
Install the fuel tank and 2 fuel tank bands with the 2 clips, 2 pins and the 2 bolts.
- Torque:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
| 7. CONNECT FUEL TANK BREATHER TUBE |
![]() ![]() |
![]() ![]() |
Push |
Connect the fuel tank breather tube.
Align the fuel tank breather tube connector with the pipe, then push in the fuel tank vent connector until the retainer makes a click sound.
- NOTICE:
- Check that there are no scratches or foreign matter on the disconnected parts of the fuel tank vent connector and pipe before performing the work.
- After connecting the fuel tank breather tube, check that the fuel tank breather tube is securely connected by pulling the quick connector.
- Check that there are no scratches or foreign matter on the disconnected parts of the fuel tank vent connector and pipe before performing the work.
| 8. CONNECT FUEL CUT-OFF TUBE |
Push the tube connector into the pipe until the connector makes a click sound.

Text in Illustration 

Push
- NOTICE:
- Check that there is no damage or foreign objects on the connected part of the pipe.
- After connecting, check that the pipe and the connector are securely connected by pulling them.
- Check that there is no damage or foreign objects on the connected part of the pipe.
| 9. CONNECT FUEL TANK MAIN TUBE AND FUEL TANK RETURN TUBE |
Push the tube connector into the pipe until the connector makes a click sound.

Text in Illustration *1
Retainer
*2
O-Ring
*a
*Lock
*b
*Unlock
- NOTICE:
- Check that there is no damage or foreign objects on the connected part of the pipe.
- After connecting, check that the pipe and the connector are securely connected by pulling them.
- Check that there is no damage or foreign objects on the connected part of the pipe.
| 10. CONNECT FUEL TANK TO FILLER PIPE HOSE |
Connect the fuel tank to filler pipe hose, as shown in the illustration, with the clamp.

| 11. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Automatic Transmission) |
Install the fuel tank protector with the 4 nuts.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
Install the fuel tank protector bracket with the 2 nuts.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
| 12. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Manual Transmission) |
Install the fuel tank protector with the 4 nuts.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
Install the fuel tank protector bracket with the nut.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
| 13. INSTALL REAR FLOOR SERVICE HOLE COVER |
Connect the connector.
Install the 3 screws to the center floor.
Install the center floor silencer pad LH.
Install the floor carpet.
| 14. INSTALL REAR DOOR SCUFF PLATE LH |
Engage the 6 claws and install the rear door scuff plate.
| 15. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 14 claws and install the front door scuff plate.
| 16. INSTALL REAR SEAT CUSHION ASSEMBLY LH |
Install the rear seat cushion assembly LH with the 2 bolts.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 17. INSPECT FOR FUEL LEAK |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
- NOTICE:
- Do not start the engine.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Speed / ON.
Check fuel pump operation.
Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.
If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.


