2011-2016 FJ Cruiser · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014


1. INSTALL FAN
  1. Install the fan onto the coupling with the 4 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


2. INSTALL FAN SHROUD
  1. Install the fan pulley to the engine water pump assembly.

  1. Place the fan shroud together with the fan and fluid coupling assembly between the radiator assembly and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. A226673E01
    Align the paint marks of the same color (pink to pink and black to black) on the stud bolts of the engine water pump assembly and the outer flange of the fan and fluid coupling assembly, and assemble the parts.
    Text in Illustration 
    *a
    Paint Mark

  1. Temporarily install the fan and fluid coupling assembly to the engine water pump assembly with the 4 nuts. Tighten the nuts as much as possible by hand.

  1. A287972E01
    Engage the 2 guides of the fan shroud to the radiator assembly as shown in the illustration.
    Text in Illustration 
    *1
    Oil Cooler Hose

  1. Install the fan shroud to the radiator assembly with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the radiator reserve tank assembly to the radiator assembly with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the 2 oil cooler hoses to the hose clamp and engage the clamp.

  1. A225650E01
    Set the fan and generator V belt onto every part.
    Text in Illustration 
    *1
    Vane Pump Assembly
    *2
    Engine Water Pump Assembly
    *3
    No. 2 Idler Pulley Sub-Assembly
    *4
    Generator Assembly
    *5
    Cooler Compressor Assembly
    *6
    No. 1 Idler Pulley Sub-Assembly
    *7
    Crankshaft Pulley
    *8
    V-ribbed Belt Tensioner Assembly

  1. While turning the V-ribbed belt tensioner assembly counterclockwise, remove the pin.

    NOTICE:
    Make sure that the fan and generator V belt is properly set to each pulley.

  1. Check that the belt fits properly in the ribbed grooves.

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.

  1. Tighten the 4 nuts of the fan and fluid coupling assembly.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the radiator reserve tank hose to the radiator assembly.


3. INSTALL UPPER RADIATOR SUPPORT SEAL

  1. A226651
    Engage the 7 clips to install the upper radiator support seal to the fan shroud.


4. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Hook the engine under cover to the frame.

  1. Install the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


5. INSTALL V-BANK COVER
  1. Engage the 2 hooks to install the V-bank cover to the No. 1 V-bank cover bracket.

  1. Align the 2 cushions of the V-bank cover with the 2 pins and press down on the V-bank cover to engage the 2 cushions to the 2 pins.

← INSTALLATION (Nov 2010 – Jul 2014)COMPONENTS (Jul 2007 – Jul 2009) →