INSTALLATION
Removal / installation · Vehicles built from Jul 2007
| 1. INSTALL REAR COIL SPRING |
![]() ![]() |
Install the coil spring to the rear axle housing.
- HINT:
- Fit the lower end of the coil spring into the gap of the spring lower seat.
| 2. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER |
![]() ![]() |
Install the shock absorber and temporarily tighten the bolt.
| 3. STABILIZE SUSPENSION |
Jack down the vehicle.
Bounce the vehicle up and down several times to stabilize the suspension.
| 4. FULLY TIGHTEN REAR SHOCK ABSORBER |
![]() ![]() |
Fully tighten the bolt.
- Torque:
- 98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }
| 5. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE |
![]() ![]() |
Install the 2 flexible hoses with 2 new clips.
Using a union nut wrench, install the 2 brake tubes onto the flexible hose.
- Torque:
- without union nut wrench:
- 15 N*m{ 154 kgf*cm , 11 ft.*lbf }
- with union nut wrench:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
- NOTICE:
- This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.886 in.) (Click here).
- This torque value is effective when union nut wrench is parallel to a torque wrench.
- This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.886 in.) (Click here).
| 6. BLEED BRAKE LINE |
Turn the ignition switch to ON.
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.
Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.
Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.
- Torque:
- 11 N*m{ 110 kgf*cm , 8 ft.*lbf }
Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.
With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.
- HINT:
- Air is bled as the pump motor operates while the brake pedal is being depressed.
- Be sure to release the brake pedal to stop the motor after approximately 100 seconds of continuous operation.
- As brake fluid is continuously drained while the pump operates, it is not necessary to repeatedly depress the brake pedal.
- Air is bled as the pump motor operates while the brake pedal is being depressed.
When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.
- Torque:
- 11 N*m{ 110 kgf*cm , 8 ft.*lbf }
Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.
Turn the ignition switch off.
Inspect for brake fluid leaks.
Check and adjust the brake fluid level (Click here).
Clear the DTCs (Click here).
| 7. INSTALL REAR WHEEL |
- Torque:
- 112 N*m{ 1,137 kgf*cm , 82 ft.*lbf }




