2011-2016 FJ Cruiser · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

C093595E01
  1. Install a new rear differential drive pinion bearing spacer.

    HINT:
    Install the spacer in the correct direction.


2. INSTALL DIFFERENTIAL OIL STORAGE RING

  1. C216531E01
    Using SST and hammer, tap in a new differential oil storage ring.
    SST
    09308-14010  

    NOTICE:
    Be careful not to damage the oil storage ring.


3. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

C216532E01
  1. Using SST and hammer, tap in the rear drive pinion front roller bearing (outer).

    SST
    09308-14010  
    09309-14040  

  1. Install the rear drive pinion front roller bearing (inner).


4. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

  1. C216536
    Install the rear differential drive pinion oil slinger.


5. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

C216533E01
Text in Illustration 
*1
Oil Seal Depth
  1. Apply MP grease to the lip of a new oil seal.

  1. Using SST and hammer, tap in the rear differential carrier oil seal.

    SST
    09214-76011  

    Oil seal depth:
    -0.30 to 0.30 mm (-0.012 to 0.012 in.)


6. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

C217280E01
  1. Using SST, install the rear drive pinion companion flange sub-assembly.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. B087843E01
    Using SST to hold the companion flange in place, install the rear drive pinion nut.
    SST
    09330-00021   (09330-00030)

    Torque:
    457 N*m{ 4,660 kgf*cm , 337 ft.*lbf } or less


7. INSTALL DIFFERENTIAL DRIVE PINION PRELOAD

C089308E01
  1. Using a torque wrench, measure the preload.

    Preload (at starting):
    Bearing
    Standard
    New bearing
    0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf)
    Used bearing
    0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)

    If the result is not as specified, adjust the preload.


8. STAKE REAR DRIVE PINION NUT

C089310E01
  1. Using a chisel and hammer, stake the rear drive pinion nut.


9. INSTALL REAR PROPELLER SHAFT ASSEMBLY
  1. Install the rear propeller shaft assembly (Click here).


10. ADD DIFFERENTIAL OIL

D025304E05
  1. Stop the vehicle on a level surface.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. After changing the oil seal, drive the vehicle and then check the oil level again.
    1. Too much or too little oil will lead to differential problems.

    HINT:
    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Differential oil type and viscosity:
    Toyota Genuine Differential gear oil LT 75W-85 API GL-5 SAE 75W-85 or equivalent


    Differential Oil Capacity:
    Item
    Capacity
    Front Differential
    w/o A.D.D.
    1.35 to 1.45 Liters
    (1.43 to 1.53 US qts, 1.19 to 1.28 Imp qts.)
    w/ A.D.D.
    1.50 to 1.60 Liters
    (1.59 to 1.69 US qts, 1.32 to 1.41 Imp qts.)
    Rear Differential
    w/o Differential Lock
    2.45 to 2.55 Liters
    (2.59 to 2.69 US qts, 2.16 to 2.24 Imp qts.)
    w/ Differential Lock
    2.40 to 2.50 Liters
    (2.54 to 2.64 US qts, 2.11 to 2.20 Imp qts.)

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug with a new gasket.

    Torque:
    Front differential:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }
    Rear differential:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


11. INSPECT DIFFERENTIAL OIL LEAK
← INSTALLATION (Jul 2007 – Jul 2009)COMPONENTS (Jul 2007 – Jul 2009) →